Manual Silvercrest SKV 1200 B2 - IAN 292161 (page 27 of 117) (English, German, Dutch, French, Portuguese, Spanish)

679193

Zoom out

Zoom in

1/117

│

IE│ 23 ■

SKV 1200 B2

Working with the blender

WARNING! RISK OF INJURY!

► Always allow hot ﬂuids to cool down to a

lukewarm temperature (approx. 30–40°C)

before adding them into the blender t.

WARNING! RISK OF INJURY FROM

SHARP BLADES/ROTATING DRIVE

UNIT!

► Never put your hand into the attached

blender t!

► Do not remove the blender t unless the

blades z are stationary.

► Operate the blender t only when the blender

lid r with the measuring cup e are attached.

► In cases of malfunction, switch the appliance

oﬀ and remove the plug from the wall socket

to prevent the appliance from being switched

back on unintentionally.

AttENtION! PrOPErty dAmAgE!

► Never use the mixing bowl 6 and blender t

at the same time! This will overload the motor!

► When working with the blender t we recom-

mend allowing the appliance to cool down

after 3 minutes of operation.

Proceed as follows to prepare the blender for

operation t. Use ﬁgure C on the rear fold-out

page as a guide.

1) Press down the release lever 2 and press the

swivel arm 1 downwards into the working

position.

2) Turn the drive protection cover u clockwise so

that the arrow on the drive protection cover u

is pointing to the

symbol on the appliance.

Remove the drive protection cover u and

place it to one side.

WARNING! RISK OF INJURY!

► Ensure that the rotary switch 3 is turned to

"0" before you place the blender t on the

blender drive i. Otherwise the appliance will

start immediately as soon as the blender t

has locked into place.

3) Place the blender t on the blender drive unit

i so that the lock tabs on the underside of

the blender t lock into the recesses on the

blender drive unit i. The

symbol on the

blender t must be pointing to the

symbol

on the appliance. Turn the blender t anti-

clockwise as far as it will go. The symbol

on the blender t must then be pointing to the

symbol on the appliance.

4) Remove the blender lid r by turning it anti-

clockwise until it disengages from the catch on

the blender t and then pull it upwards and

oﬀ.

5) Add the ingredients.

6) Press the blender lid r

with the measuring cup e

slightly oﬀset ﬁrmly back onto the blender t.

Close the blender lid r by turning it clockwise

as far as the stop

back into the catch

on the

blender t. Ensure that the pouring spout on

the blender t

is closed.

7) Turn the rotary switch 3 to the desired setting.

NOtE

► The ideal speed depends on the consistency

of the items being mixed. The more liquid the

contents are, the faster you can mix them.

► For short, powerful pulsed operation, turn

the rotary switch 3 anticlockwise to level P.

Level P does not lock into place so as not

to overload the motor. You should therefore

keep the rotary switch 3 in this position only

for a short time.

cruSHINg IcE

► In order to produce crushed ice, place ice

cubes in the blender t, close it and turn the

rotary switch 3 approx. 7 times to level P

for 5 seconds. You may need to adapt the

above instructions depending on the quantity

and size of the ice cubes.

IB_292161_SKV1200B2_LB8.indb 23 22.09.17 07:53

Dobrý den, chcem dokupit prislušenstvo k kuchynskemu robotu IAN 292161 Jedná sa o mlyncek na mäso a dalšie mlyncek na rezance. Dakujem Peter Zelinka Slovakia. Submitted on 3-11-2020 at 22:19
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SKV 1200 B2 - IAN 292161 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 3,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Silvercrest SKV 1200 B2 - IAN 292161 Manual

Product: