575461

Silvercrest SKD 2300 A1 - IAN 90866 Manual

57
Zoom out
Zoom in
Previous page
1/62
Next page
SKD 2300 A1 55
3. Press the “Reduce temperature”
button 17 to lower the desired
temperature to a minimum of 5 °C
(41 °F).
Selected specified temperature 20 is
shown in display 5.
6.3 Setting the heat setting
The appliance has three heat settings:
– 1,000 watts
– 1,300 watts
– 2,300 watts
1. Press button 25 repeatedly until the
desired heat setting is set.
Selected heating level 11 is shown in
display 5.
2. Press the fan button 15 to switch the fan
on or off.
If the fan is switched on, "Fan"
symbol 12 is shown in display 5.
Note: The fan might make a slight
noise, but it does ensure better
circulation of the heated air.
6.4 Setting the heating time
The appliance has a timer for setting the
heating time to between 1 and 15 hours.
The appliance switches off automatically
once the heating time has expired.
1. Press timer button 18 repeatedly until
desired running time 19 is shown in
display 5.
2. To switch off the timer, press timer
button 18 repeatedly until running
time 19 is no longer displayed.
6.5 Thermal cut-out
For your safety the appliance has a thermal
cut-out.
If the temperature inside the appliance
becomes too high, the appliance switches
off automatically:
1. Switch the mains switch 9 to "0" to
switch off the appliance.
2. Check whether the air inlet 6 or outlet 4
is obstructed and remove the cause.
If you cannot establish a cause and the
fault occurs repeatedly, have the
appliance repaired or else take it out of
use.
3. Wait for the appliance to cool down.
4. You can then continue to operate it
normally.
6.6 Frost protection
To prevent the temperature in a room falling
below 0°C (32°F), proceed as follows:
1. Press the button for selecting heating
level 25 repeatedly until "Frost
protection" symbol 13 appears in
display 5.
As soon as the temperature in the immediate
vicinity of the appliance drops significantly
below 7 °C (44 °F), the heating
automatically switches on.
As soon as the temperature rises to above
9 °C (48 °F), the heating switches off and
display 5 shows room temperature again.
2. To switch off frost protection, press the
button for selecting heating level 25
repeatedly until "Frost protection"
symbol 13 in display 5 disappears.
RP90866 Konvektor LB1 Seite 55 Dienstag, 2. Juli 2013 3:36 15
… 57 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SKD 2300 A1 - IAN 90866 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SKD 2300 A1 - IAN 90866 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info