793041

Silvercrest SHSS 28 A1 - IAN 394516 Manual

13
Zoom out
Zoom in
Previous page
1/176
Next page
SHSS 28 A1■ 10 │ GB│IE
Emptying the dirt container and
cleaning the filter
NOTE
► To achieve the best results, empty the dirt
container 7 and clean the HEPA filter 5
regularly.
► If you need a new HEPA filter 5, please
contact our customer service department
(see section Ordering replacement parts).
1) To open the dirt container 7, remove the
hand element 3 from the hand element
recess e.
2) Press the release button 4 and, at the
same time, pull the dirt container 7 forwards
and off.
3) Start by pulling the HEPA filter 5 and then
the coarse filter 6 out of the dirt container 7
(Fig. 4). Tap out both parts over a rubbish bin
or similar. If necessary, you can rinse out the
HEPA filter 5 with fresh water. Allow it to air
dry fully afterwards.
Fig. 4
4) Empty the dirt container 7 into the rubbish
bin or similar.
5) First re-insert the coarse filter 6 and then the
dry HEPA filter 5.
6) Replace the dirt container 7 onto the hand
element 3 by first pushing the lower catch on
the hand element 3 into the recess on the dirt
container 7. Then, press the upper part of the
dirt container 7 onto the hand element 3
until the dirt container 7 clicks into place
and sits firmly.
Cleaning the appliance
Wipe the appliance with a damp cloth. For stub-
born dirt, add a little mild detergent to the cloth. En-
sure that the appliance is completely dry before
using it again.
Cleaning the rotary brush
The rotary brush r should be checked regularly
for blockages; any hair, threads or dirt should be
removed. Remove the rotary brush r as follows:
1) Turn the floor nozzle upside down.
2) Push the catch on the cover plate towards
the symbol and remove the cover plate
(Fig. 5).
3) Remove the rotary brush r.
4) Remove any dirt (on both sides of the brush
bristles) and clean the rotary brush r.
To do this, take a damp cloth and wipe the
individual bristle bundles from the inside to
the outside.
5) To replace the rotary brush r, first push the
broad end onto the drive shaft so that the
rotary brush r hooks into place.
6) Then, push the other end into the mount so
that the rotary brush r sits straight in the floor
nozzle.
7) Reattach the cover plate until it clicks firmly into
place. The cover plate locks automatically as
the latch moves towards the symbol (Fig. 5).
Fig. 5
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SHSS 28 A1 - IAN 394516 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SHSS 28 A1 - IAN 394516 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2.81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info