777999

Silvercrest SHBS 700 A1 - IAN 354063 Manual

14
Zoom out
Zoom in
Previous page
1/67
Next page
14 GB/IE/NI
Place the thinning attachment 12 onto the pro-
duct as described in the chapter “Changing
the attachments.“
Note: The thinning attachment 12 prevents
every hair from being cut.
Trimming beards
Note that the desired trim length can only be
achieved if the product is held perpendicularly
to the skin‘s surface.
Comb the beard using the supplied comb 17
in its direction of growth.
Shorten the beard downwards from the ear to
the chin, one side after the other.
Use the cutting unit 1 without the comb attach-
ment 11 to trim the beard very short or to trim
a moustache or hairline.
Graduate the desired trim length by rotating
the lower part of the product 5 according to
length position indicator 4. The trim length
may be set to 5 different levels (0.8 mm/
1.1 mm/1.4 mm/1.7 mm/2.0 mm).
To trim a moustache, firstly comb it straight
downwards. Begin in the centre above the
mouth, then one side and then the other.
Cleaning and care
CAUTION! DANGER TO LIFE BY ELECTRIC
SHOCK! Pull the plug-in mains adapter 7 out
of the mains socket before cleaning the product.
Never touch the plug-in mains adapter 7 with
moist or wet hands, especially when you plug
it into the socket or pull it out of the socket.
Always keep the plug-in mains adapter 7 and
supply cord dry.
CAUTION! RISK OF PROPERTY DA
MAGE!
Do not submerge the product in water or any
other liquid to clean it as the product is not
waterproof. This could damage the live parts
(rechargeable batteries).
Do not use any corrosive or abrasive cleaning
agents.
Clean the housing and the charging base 6
using a damp cloth and a mild detergent.
Switch the product off by pressing the ON/
OFF button 3 b once or twice, until the indicator
light 3 a goes off.
Disconnect the supply cord from the product
and remove the plug-in mains adapter 7 from
the mains socket.
Remove the comb attachment 11 , the thinning
attachment 12 or the cutting unit 1 from the
product (see Fig. G + H).
Wash the comb attachment 11 , the thinning
attachment 12 or the cutting unit 1 with run-
ning water if necessary.
Dry the comb attachment 11 , the thinning
attachment 12 or the cutting unit 1.
Remove the cutting unit 1 (see Fig. H).
Remove any remaining bits of hair from the
cutting unit 1 using the cleaning brush 13
provided (see Fig. I).
Apply one or two drops of blade oil 14
between the blades and the moving parts
(see Fig. J).
Adjust the length position indicator 4 to
2.0 mm after you have finished cleaning the
product, before once more attaching the
cutting unit 1 to the product (see Fig. K).
Note: Clean the cutting unit 1, comb attach-
ment 11 and thinning attachment 12 after
every use.
Storage
Place the product in the charging base 6 if
you wish to store it. Alternatively, you can also
store it in the travel case 16 provided.
Troubleshooting
Error Cause Solution
The product
does not
work.
The battery
may not be
charged.
Recharge the
product.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SHBS 700 A1 - IAN 354063 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SHBS 700 A1 - IAN 354063 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1.53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info