663328
11
Zoom out
Zoom in
Previous page
1/78
Next page
9
GB
7. Cleaning and care
DANGER! Risk of electric
shock!
Unplug the power unit8 from the wall sock-
et before cleaning the hair and beard trim-
mer4 and the battery charger9.
WARNING! Risk of injury!
Always switch the hair and beard trimmer4
off before cleaning.
WARNING! Risk of material damage!
Do not use any astringent or abrasive clean-
ing agents.
NOTE: clean and oil the device after every
use.
Hair and beard trimmer4 and
battery charger
9
Wipe the casing of the hair and beard
trimmer and the battery charger with a
damp cloth.
Comb attachments1 / thinning
out attachment
2
Remove the comb attachment1 / thin-
ning out attachment2. Rinse the comb
attachment/thinning out attachment
with water and let it dry before using it
again.
Trimmer attachment3
1. Figure E: remove the trimmer attach-
ment3 from the hair and beard trim-
mer4 by pressing it with the thumb
towards the rear.
2. Remove the hair remnants from the at-
tachment using the cleaning brush12
included in the delivery.
3. Apply a few drops of blade oil11 to
the cutting edge of the attachment. Us-
ing a soft cloth, wipe off the surplus oil,
if necessary. Only use acid-free oil,
such as e.g. sewing machine oil.
4. Figure F: to attach the attachments,
put the lower flap of the attachment3
into the slot in the hair and beard trim-
mer4 and press the upper part of the
attachment against the hair and beard
trimmer until it audibly locks into place
and sits firmly in position.
8. Storage and
transport lock
For storage
put the hair and beard trimmer4 in
the battery charger9 or
use the included travel case14.
If the transport lock is activated, a lock
symbol appears on the display7 .
- Press and hold the on/off switch 6
for approx. 3 seconds, in order to
switch the transport lock on/off.
- Connecting the power unit8 deacti-
vates the transport lock, which cannot
be activated during mains operation.
9. Disposal
The symbol showing a wheel-
ie bin crossed through indi-
cates that the product
requires separate refuse col-
lection in the European Un-
ion. This applies to the
product and all accessories marked with this
symbol. Products identified with this symbol
may not be discarded with normal house-
hold waste, but must be taken to a collection
point for recycling electric and electronic ap-
pliances. Recycling helps to reduce the con-
sumption of raw materials and protect the
environment.
Packaging
When disposing of the packaging, make
sure you comply with the environmental reg-
ulations applicable in your country.
BB*5$B%ERRN6HLWH'LHQVWDJ1RYHPEHU
11


Need help? Post your question in this forum.

Forumrules
1

Forum

silvercrest-shbs-600-a1---ian-275147

Reset search

  • Mines completely stopped working. wont recharge. Only had it long enough to recharge it about 3 times! Submitted on 18-7-2018 at 09:56

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SHBS 600 A1 - IAN 275147 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SHBS 600 A1 - IAN 275147 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info