646936
22
Zoom out
Zoom in
Previous page
1/90
Next page
20
GB
7. Press the button|2 . The red LED|1
lights up. The film is being sealed.
- After approx. 5 - 7 seconds, the red
LED|1 goes out and the sealing pro-
cess is completed.
8. Simultaneously, press buttons|8 in order
to release the lock of the lid|11.
9. Open the lid|11 and remove the bag.
10. Check the welding seam. It should be a
smooth creaseless seam.
8.3 Vacuum-pack and seal
the bag
DANGER! Risk of electric
shock due to moisture!
~ For vacuum packing, no liquids must be
inside the bag.
~
Ensure that no liquid is sucked in during
the extraction of air. If this occurs, interrupt
the process by pressing the button|
3
.
1. Smooth the bag where it is to be
sealed.
2. Open the lid|11.
3. Figure A: place the bag in the device.
For this purpose, the end of the film
must be positioned shortly in front of the
rear limitation webs|12 and the lateral
limitation webs|15.
4. Ensure again that there are no creases
in the film - especially in the area above
the welding wire|14.
5. Close the lid|11.
6. Figure B: use both hands to press firm-
ly on the edges of the lid|11. They must
engage audibly.
7. Press the button|
4
. The green LED|
5
lights up. The vacuuming starts.
- After the vacuuming, the green LED|5
goes out and the red LED|1 lights up -
the sealing process is active. After ap-
prox. 5 - 7 seconds, the red LED|1
goes out and the sealing process is
completed.
8. Simultaneously, press buttons|8 in order
to release the lock of the lid|11.
9. Open the lid|11 and remove the bag.
10. Check the welding seam. It should be a
smooth creaseless seam.
9. Cleaning and
storage
DANGER! Risk of injury
through burning/scalding!
~ Allow the device to cool down com-
pletely before you clean it or put it
away.
~ The welding wire|14 becomes very hot
during operation. Do not touch the hot
welding wire|14.
DANGER! Risk of electric
shock!
~ Prior to cleaning, disconnect the mains
plug|6 of the device.
DANGER! Risk of electric
shock due to moisture!
~ The device, the power cable|6 and the
mains plug must not be immersed in
water or any other liquids.
WARNING! Risk of material
damage!
~ Do not use any astringent or abrasive
cleaning agents.
9.1 Cleaning
In order to ensure the proper function and
the full capacity of your device, clean it reg-
ularly.
Wipe down the housing of the device
with a damp cloth.
Prior to the next use, the device must be
completely dry.
BB&3(B)ROLHQVFKZHLVVJHUDHWB%ERRN6HLWH'LHQVWDJ$SULO
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SFS 110 B2 - IAN 277100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SFS 110 B2 - IAN 277100 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 2,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info