628971

Silvercrest SFR 3.7 A2 - IAN 106437 Manual

9
Zoom out
Zoom in
Previous page
1/74
Next page
6
SFR 3.7 A2
GB
IE
Prior to fi rst use
Assembling the appliance
1) Remove all packaging materials from the
appliance.
2) Push the vacuum attachment 1 onto the
connecting piece 2.
NOTE
► This appliance is supplied with non-charged
batteries. The batter
ies must be charged for
3.5 hours before the fi rst use.
3) Charge the appliance (see Chapter “Charging
the appliance”).
The appliance is now ready for use.
Operation
ATTENTION! DAMAGE TO PROPERTY!
► Do not use foaming, corrosive, aggressive,
abr
asive or chemical cleaning agents.
These can damage the appliance.
1) Set the tip of the spray nozzle q to STREAM
(fi ne water mist) or SPRAY (coarse water mist).
2) Attach the spray nozzle q to the wiping attach-
ment 0.
3) Place the positioning ring w over the tube and
put it onto the spray nozzle q so that it clicks
into place.
4) Fill the spray bottle with water and, if desired,
with a cleaning agent suitable for window
cleaning e.
5) Screw the spray nozzle q with the fi tted
wiping attachment 0 onto the spray bottle e.
6) Pull the microfi bre attachment z over the
retainer on the wiping attachment 0 and
secure it with the velcro fastener.
7) Spray the surface that you wish to clean.
8) Using the microfi bre attachment, z wipe over
the sprayed areas and loosen any stubborn
dirt.
9) Press the on/off switch 6. The indicator light 8
lights up red.
NOTE
► If the indicator light 8 fl
ashes red during
use, this indicates that the appliance needs
to be charged (see chapter on "Charging the
appliance").
10) Move the blade of the vacuum attachment 1
slowly from top to bottom across the wet
surfaces. The moisture is removed and sucked
into the dirt container 5.
NOTE
► Never drag the blade sideways across wet
sur
faces. Doing so prevents the water from
being vacuumed up; instead, it runs off the
side of the blade.
11) After you have fi nished a section, always start
again at the top.
ATTENTION! DAMAGE TO PROPERTY!
► Only continue working until the MAX mark
on the dir
t container 5 is reached. Then
switch off the appliance and empty the dirt
container 5.
Remove the plug on the dirt container 5.
Pour away the dirty water and reclose the dirt
container 5. You can then resume working.
12) Once the entire surface is dry, press the on/
off switch 6 again to switch the appliance off .
The indicator light 8 goes out.
13) If necessary, dry off any streaks or remaining
moisture on the surface with a dry cloth.
Charging the appliance
NOTE
► Ensure that the appliance is switched off
befor
e starting to charge the batteries.
■ To charge the appliance, connect the charger t
to a mains sock
et and insert the connecting jack
r into the charging socket 9 on the motor unit 7.
The indicator light 8 lights up red. When the
appliance is fully charged, the indicator light 8
lights up green.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SFR 3.7 A2 - IAN 106437 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SFR 3.7 A2 - IAN 106437 in the language / languages: English, German, Dutch, Danish, French, Swedish, Finnish as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info