628972
18
Zoom out
Zoom in
Previous page
1/76
Next page
SilverCrest SFR 2.4 B1
16 English
Getting Started
Powering the Headphones On/Off
If the battery level of the headphones is high enough (the power and charge indicator (18) on the
transmitter must light green), you may remove the headphones from the transmitter cradle.
You may optionally power the headphones using conventional batteries. For more information,
see the information on page 19 – “Battery Operation”.
1. Press the On/Off button (9) of the headphones once to switch them on. The power indicator
(8) will light up orange.
2. Keep the On/Off button (9) on the headphones pressed for a few seconds to switch them
back off. The power indicator (8) then goes out.
Please remember to set the correct position for the Power source DC1/DC2
selection switch (10). When set at DC2 position, the device will power on only
if charged batteries have been inserted into the headphones. Please also see
page 20 – “Powering the Headphones by Using Batteries”.
In wireless mode, if no audio signal is received for 5 minutes, the headphones
switch off automatically. You will have to switch the headphones on again
next time you use them.
Selecting the Operating Mode
1. Slide the mode selection switch (6) to the “WL” position to use the wireless headphones to
listen to an external audio source (e.g. your hi-fi equipment).
2. Slide the mode selection switch (6) to the “FM” position to receive your favourite FM radio
programmes.
Powering the Transmitter Cradle On
1. To power the transmitter cradle on, slide the On/Off switch (12) to the “ON” position.
After powering on, the send indicator (17) blinks green. This indicates that the transmitter
cradle is attempting to establish a connection with the headphones. See also the description
on page 17 – “Synchronising the Headphones and Transmitter Cradle”.
Synchronising the transmitter cradle and the headphones can take a while.
If no audio signal is received, the transmitter cradle automatically disconnects
the RF link after 10 minutes. Once the audio signal is reactivated, the RF link is
restored automatically.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SFR 2.4 B1 - IAN 75760 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SFR 2.4 B1 - IAN 75760 in the language / languages: English, German, Danish as an attachment in your email.

The manual is 5,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info