739556

Silvercrest SFR 1200 A1 IAN 74435 Manual

40
Zoom out
Zoom in
Previous page
1/45
Next page
40 GB
Use / Cleaning and maintenance
Wet shave
Use a fine-bubbled shaving foam.
CAUTION! We advise against the use of
shaving gel, as it can stick the foil
4
and the
cutter set
12
together.
Apply a thin layer of shaving foam to your
face. Shaving foam is the most suitable choice
from the wide range of available cosmetic
shaving products. Do not use a thick layer of
shaving foam, as this can detrimentally affect
the performance of the shaver.
Proceed with the shave in all other respects as
described in the section “Foil shave”.
If the shaving head
9
becomes blocked, rinse
the shaver under running water (refer to the
section “Wet cleaning”).
Trimmer
The trimmer
1
on the back of the device can be
switched on by pushing it out into the locked position.
Slide the trimmer towards the shaving head
9
as
far as it will go.
It can be used for shortening longer beard hair,
trimming contours, sideburns and walrus moustaches.
After use, slide the trimmer
1
back into its initial
position.
3-day beard attachment
The supplied protective cap
2
can be used as a
3-day beard attachment. Regular use of this attach-
ment allows you to create the effect of a three day
beard.
Note: Please note that using the 3-day beard at-
tachment produces a shave corresponding to anything
between a 3-day and a 7-day beard, depending
on the rate of growth of your beard.
Place the protective cap
2
on to the shaving
head
9
and ensure it engages. The trimmer
1
is now blocked by the protective cap
2
.
To switch on the device, slide the ON / OFF
switch
7
upwards. You can now trim your beard.
To switch off the device, slide the ON / OFF
switch
7
downwards.
Note: When you are using the protective
cap
2
as a 3-day beard attachment, the direct
contact of the foil with your skin is lost. The nat-
ural lubrication of the cutting system by the secre-
tions from your skin no longer takes place. After
each use of the 3-day beard attachment, spread
a drop of cutter or sewing machine oil on the
foil after cleaning. This will preserve the excellent
shaving performance of your shaver.
Take off the protective cap
2
if you wish to
have a “1-day shave” without using the 3-day
beard attachment, or if you wish to use the
trimmer
1
. Detach the protective cap
2
from
the shaving head
9
to do this.
Cleaning and maintenance
Cleaning
CAUTION! RISK OF ELECTRIC SHOCK!
Always disconnect the shaver from the mains
supply and the flex before cleaning it. Do not
immerse into water or other fluids!
Always clean the razor after each use in order
to ensure it works well.
When cleaning the appliance regularly with warm
water, occasionally moisten the long hair trim-
mer
1
and cutter set
12
with sewing machine
oil.
Dry cleaning:
CAUTION! Do not clean the foil with the brush
as this could damage it. Do not remove the foil!
Press the release buttons
5
on the side and
pull the shaving foil frame
3
out or blow it out.
Knock the shaving foil frame
3
out on an even
surface.
Brush the cutter set
12
with the cleaning brush.
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SFR 1200 A1 IAN 74435 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SFR 1200 A1 IAN 74435 in the language / languages: French as an attachment in your email.

The manual is 1,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Silvercrest SFR 1200 A1 IAN 74435

Silvercrest SFR 1200 A1 IAN 74435 User Manual - English, German, Dutch - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info