539995

Silvercrest SFB 10.1 C3 Manual

102
Zoom out
Zoom in
Previous page
1/116
Next page
SilverCrest SFB 10.1 C3
100 - English
automatic search had been stopped with a slight delay and further
codes have been sent.
During the automatic search, the remote control responds to the
and buttons only.
5. After you have pressed the button to stop searching you can
press the buttons to send the previous or next codes
manually. If your device responds again to a code, you have found
a suitable code. Press to exit the automatic search. The codes
are saved and the display reads “SUCCESS”.
6. Or press to exit the automatic search. This will not save any
codes.
7. After the remote control has finished transmitting the last available
code from the code list, the search will stop and after a few seconds
the start window appears.
Press to go back one menu level. To return to the start window,
press one of the device buttons.
Direct code input (CODE SET)
1. Press and hold the button for 3 seconds.
2. Press , select “CODE SETUP” and then press .
3. Press , select “CODE SET” and press to confirm.
The selected device flashes and the currently set device code
appears on the display. At this point you can select a different device
by using the device buttons. Confirm your selection with .
4. The first digit of the 4-digit device code currently set flashes.
5. Enter the correct 4-digit code for the device selected by using the
number buttons. You can find the 4-digit code in the device code list
supplied.
6. Press to confirm the entry. The display reads “SUCCESS”
followed by “CODE SET”.
7. Invalid CODES cannot be found in the CODE list. If you enter an
invalid code “NOT FOUND” appears on the display and you can
then enter the correct code.
Press to go back one menu level. To return to the start window,
press one of the device buttons.
Flex mode
For the different device buttons there are preset code lists for specific
device groups. Normally, you will assign the corresponding device types
to the device buttons. For example, you will assign programming a VCR
to the device button, a DVD player to the device button,
etc. Furthermore, the Flex mode conveniently lets you assign a device
from any device group to the and buttons. The requisite is
that you assign the code list of the desired device group (where the
device belongs to) to the or button you want to use for
this device.
The code lists (e.g. 0 for TV or 2 for DVD) belonging to each device
group can be found in the table below:
TV VCR DVD DSAT BD AMP CBL CD
0 1 2 3 4 5 6 7
For direct code input:
1. Press and hold the button for 3 seconds.
2. Press , select “CODE SETUP” and press to
confirm.
… 102 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SFB 10.1 C3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SFB 10.1 C3 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info