793243

Silvercrest SEK 1900 A1 - IAN 412670 Manual

13
Zoom out
Zoom in
Previous page
1/178
Next page
GB/IE/NI/MT/CY12
3. Before starting up
Remove all packaging material and transport
locks from the unit. Check that the package con-
tents are complete and undamaged.
3.1 Setting up the unit
For safe and fault-free operation of the unit, the
installation site must meet the following requirements:
The floor must be firm, flat and horizontal.
Minimum distances from the housing of 90 cm
to the side, 90 cm to the top, 90 cm to the rear
and 1 m to the front must be maintained.
Do not place the unit in a hot, wet or very humid
environment or near combustible material.
The power socket must be easily accessible so
that the mains plug can be easily disconnected
if necessary.
3.2 Remote control: Inserting/changing the
battery
When supplied, a lithium coin cell 22 is included
with the remote control. In order to enable opera-
tion of the remote control, remove the plastic tape
which protrudes out of the battery compartment
20 .
If the battery in the remote control has to be re-
placed, insert a new 3 volt lithium coin cell. Pay
attention to the lithium coin cell type (CR2025)
here.
Press the lock 21 on the remote controller battery
compartment 20 to the centre. Then, pull the bat-
tery compartment 20 out.
20
21
22
Remove the used battery 22 .
Insert a new type CR2025 3 volt lithium coin
cell using the correct polarity.
Slide the battery compartment 20 back into
the remote controller until the lock 21 clicks into
position.
4. Commissioning
NOTE: FOR INITIAL USE OR IF NOT USED
FOR A LONGER PERIOD, SLIGHT ODOURS
MAY ARISE IN THE SHORT-TERM. THIS IS
NOT A MALFUNCTION AND DOES NOT
DENOTE A SAFETY RISK. PROVIDE SUFFICIENT
VENTILATION.
4.1 Standby-Modus
Plug the unit into a grounded, fused power outlet.
Set the on/off switch 2 to the "I" position to sup-
ply power to the unit. A beep will sound. The unit is
now in standby mode and the display 9 shows the
standby an.
4.2 Switching the unit on/off
Switch on the unit by pressing the on/off button on
the unit
3 or on the remote control
10
 
. The display
9
lights up. The unit is now in heating level 1 .
To switch off the appliance, press the on/off button
on the appliance
3 or on the remote control
13 . A
long beep sounds. The display 9
goes out.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SEK 1900 A1 - IAN 412670 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SEK 1900 A1 - IAN 412670 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info