Manual Silvercrest SDWH 180 A1 - IAN 285970 (page 22 of 52) (English, German, Dutch)

668039

Zoom out

Zoom in

1/52

23 GB/IE

Initial use / Use

Adjusting the time

The value (0:00) appears on the LC display

af-

ter the insulation strip has been removed from the

batteries.

If you would like to adjust the time during normal

operation, press the SET button

for 3 seconds.

The hour display will ﬂash.

Press the button

or the button

adjust the hour.

Press the SET button

to conﬁrm your entry.

The minute display will ﬂash.

Press the button

or the button

adjust the minutes.

Press the SET button

to conﬁrm your entry.

Adjusting the unit of weight

Note: The factory default setting for the scales as

supplied is “kg”. If you would like to change to „lb“

or „st“ proceed as follows:

Press the SET button

until you reach the

„0.0 kg“ display.

Then, press the SET button

for 3 seconds.

The kg unit will begin to ﬂash.

By pressing the button

within 2 seconds,

you can select the desired unit of weight.

Note: If you select the „lb/st“ unit of weight, the

height will be displayed in „feet/inches.“ If you

select the „kg“ unit of weight, the height will be

displayed in „cm“.

Use

Switching on your

scales / measuring your weight

Tip: Weigh yourself at the same time of day (pref-

erably in the morning) after visiting the toilet, with

an empty stomach and without clothing to ensure

that your results are comparable.

Place the scales down on a solid, ﬂat, horizon-

tal surface.

Note: Do not place the scales on a carpet, as

this may inﬂuence the results. If necessary you

can place a board on the carpet and place the

scales upon this. A solid ﬂoor covering is required

in order to achieve correct weight measure-

ments.

You can attach the hand-held unit

to the

scales (see Fig. A) or have the option of

holding it in your hand (see Fig. B).

Optionally: You can also hang the hand-

held unit

on a nail or screw using the slot

on the reverse side and therefore hang it to

the wall.

Important! The scales work via infrared

transmission. You must therefore ensure that

there is a direct connection between the infra-

red transmitter

on the scales and the infra-

red receiver

on the hand-held unit

There should be no obstacles between the

scales and the hand-held unit

. The infrared

transmitter

and the infrared receiver

should also not be covered.

Note: There is a limited range between the in-

frared transmitter

and the infrared receiver

(max. 1.80 m vertically).

Distribute weight evenly on both legs when you

step onto the scales. The hour display disap-

pears.

If at all possible, stand on the same areas of

the platform each time and do not move. Mov-

ing during the weighing process can lead to

discrepancies in the results. The scales will start

to measure immediately. The measurement

result will be displayed on the LC display

When the displayed weight ﬂashes thrice, the

measurement is complete.

Note: The scales are overloaded if the dis-

play shows “Err”. Do not exceed the maximum

load capacity of 180 kg (396 lb / 28 st).

Step oﬀ the platform. The LC display

will

show the time once more.

Note: Do not use the scales in the vicinity of

electromagnetic ﬁelds. This could aﬀect the

measurement results.

Safety instructions / Initial use

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SDWH 180 A1 - IAN 285970 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 3,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Silvercrest SDWH 180 A1 - IAN 285970 Manual

Product: