576652

Silvercrest SDRB 1000 B1 - IAN 102541 Manual

21
Zoom out
Zoom in
Previous page
1/24
Next page
- 18 -
Ironing function
• Dismantle the brush attachment w from the
appliance (see “Attaching/detaching the brush
attachment”).
• Connect the appliance to a correctly installed
and earthed mains power socket.
• Adjust the temperature regulator 3 as per the
international point symbols (Care Label) or the
type of material. The heating-up control lamp 5
glows. As soon as the set temperature has been re-
ached, the heating-up control lamp 5 goes out .
Note:
If doubt exists, start with a low temperature and
gradually increase it to a higher one. With sensitive
materials we recommend carrying out an ironing
test at a concealed part (inside seam).
• For heavily creased laundry, you can use the steam
function by pressing the steam blast button 8. To
generate the steam, the temperature regula-tor 3
must be set to at least ••• or higher.
• Should the heating-up control lamp 5 glow during
the process, release the steam blast button 8
and wait for a few moments until the heating-up
control lamp 5 extinguishes.
Washing label Type of
material
Temperature
regulator 3
Chemical fibres,
e.g. viscose,
polyester
•
(low
temperature)
Silk, Wool
••
(medium
temperature)
Cotton, Linen
•••
(high
temperature)
• You can repeatedly press the steam blast button 8
until the heating-up control lamp 5 glows or
water drips from the sole of the iron 0. Then, wait
until the heating-up control lamp 5 extinguishes
before activating a further blast of steam.
Note:
Should you press the steam blast button 8 whilst
the heating-up control lamp 5 is glowing the result
will be condensed water instead of steam, and water
will drip from the sole of the iron 0.
Should the water tank 1 become empty while the
appliance is in use, remove the plug 7 from the
power socket before refilling it.
• If you want to put the appliance down during
use, fold out the stands 9 to the front and place
the appliance on them. When you are ready to
reuse the appliance, simply fold the stands 9
back to the rear.
After using the steam brush
• Place the temperature regulator 3 at the
position "MIN".
• After use, ALWAYS remove the plug 7 from the
power socket.
• Pour away any water remaining in the water
tank 1 to do this, open, the water fill opening 2
of the water tank 1, turn the appliance upside
down and lightly swivel it.
IB_102541_SDRB1000B1_LB1.qxp 14.08.2014 8:45 Uhr Seite 18
DIN A5 148 mm x 210 mm
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SDRB 1000 B1 - IAN 102541 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SDRB 1000 B1 - IAN 102541 in the language / languages: English, German as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info