576652
19
Zoom out
Zoom in
Previous page
1/24
Next page
IAN 102541
DAMPFBÜRSTE SDRB 1000 B1
DAMPFBÜRSTE
Bedienungsanleitung
STEAM BRUSH
Operating instructions
- 16 -
Should the mains water at your locality be rated as
hard, it is recommended that you mix mains water
with some distilled water. Otherwise, the jets for the
steam blast function could calcify (become blocked)
prematurely.
To extend the optimal steam blast function, mix mains
water with distilled water according to the table.
The water hardness level can be queried at your
local water works.
Attention!
Before refilling with water, ALWAYS remove the po-
wer plug 7 from the mains power socket! There is
a risk of electric shock!
Lift the watertank 1 up vertically, in that you slide
the runlocking device 4 for the watertank 1 to the
rear until the watertank 1 allows itself to be lifted
off. Grasp the watertank 1 with your thumb and in-
dex finger on the hatched markings to lift it vertically
upwards. The temperature regulator 3 remains on
the appliance and is not lifted off.
Open the water fill opening 2 to the watertank 1.
Using the measuring beaker t, fill the water-
tank 1 with mains water to the "Max" marking,
but no further.
Water hardness
Ratios - distilled
water to mains
water
very soft / soft 0
medium 1 : 1
hard 2 : 1
very hard 3 : 1
Close the water fill opening 2 to the water tank 1.
Ensure that the lug on the water fill opening 2
sits in the indentation on the lid. Only in this way
is the watertank 1 properly closed.
Replace the watertank 1 back onto the appliance.
The watertank 1 must audibly engage with the
unlocking device for the watertank 4.
Attaching/detaching the brush
attachment
Attention!
NEVER attempt to attach or detach the brush attach-
ment w when the appliance is heated up.
Risk of Burns!
To use the steam and brush function, place the
brush attachment w onto the steam brush.
To do this, slide the brush attachment w all the
way along the guide to the end. The unlocking
device of the brush attachment q must engage
audibly.
To be able to use the ironing function, remove
the brush attachment w from the steam brush.
To do this, press the unlocking device q down-
wards and, at the same time, pull the brush attach-
ment w away to the front.
Steam brush function
Place the brush attachment w onto the applian-
ce. This must engage audibly with the unlocking
device on the brush attachment q.
Insert the power plug 7 into a correctly installed
and earthed mains power socket.
To generate steam, set the temperature regulator 3
to at least ••• or higher. The heating-up control
lamp 5 glows. As soon as the set temperature has
been reached, the heating-up control lamp 5
goes out.
IB_102541_SDRB1000B1_LB1.qxp 14.08.2014 8:45 Uhr Seite 16
DIN A5 148 mm x 210 mm
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SDRB 1000 B1 - IAN 102541 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SDRB 1000 B1 - IAN 102541 in the language / languages: English, German as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info