612082
8
Zoom out
Zoom in
Previous page
1/83
Next page
10 GB
Initial Operation
the appliance. The indicator on the LCD-display
13
switches back to the time indicator
20
again (see fig. A).
Note: If the supply of water is used up during
use, a signal tone will sound. The steaming
process gets stopped. The indicator on the
LCD-display
13
switches back to the time indi-
cator
20
again (see fig. A). Therefore, regularly
check the water level on the water level indica-
tor
12
and replenish sufficient water in good
time!
ATTENTION! HAZARD OF BURNS!
Make sure that the water does not exceed the
MAX mark
19
. Otherwise, hot water may spurt
out of the steamer during operation.
Q
Using Delay-Start Function
Note: Consider that the base of the appliance /
water tank
10
has to be filled with water at least
up to the MIN mark
9
. Ensure that the turbo ring
8
as well as the condensate collection basin
7
are positioned correctly.
j Press the PROG button
17
. In the LCD-display
13
, the time indicator
20
as well as the PROG
symbol
21
(see fig. A) will appear.
j Press the PLUS / MINUS button
16
, to increase
the delay time in 10-minute steps or decrease it
in 1-minute steps to achieve the desired delay.
Note: The set delay time refers to the current
clock time. That means if you set a delay time
of 30 minutes at 13:00, the steaming process
will start at 13:30. The maximum delay time is
24 hours.
j Press the PROG button
17
again.
j Press the PLUS / MINUS button
16
to increase
the steaming time in 5-minute steps or decrease
it in 1-minute steps.
Note: The maximum steaming time is 90 minutes.
Note: Be aware that you might have to replen-
ish water when the steaming time is longer. Use
the openings on the sides of the condensate
collection basin
7
for refilling. If the base of
the appliance / water tank
10
is filled up to
the MAX mark
19
, it will be sufficient for approx.
1 hour of steaming.
j Press the PROG button
17
again. In the LCD-
display
13
the time indicator
20
as well as the
PROG symbol
21
will appear. The delay-start
is now activated.
j If the set delay time is elapsed, a signal tone
will sound, the pilot lamp
15
will glow red and
the appliance will start the steaming process
automatically.
ATTENTION! HAZARD OF BURNS!
The appliance will become hot during use.
Beware of getting in contact with the ascending
steam or any components.
Note: The device starts to beep as soon as
the water in the reservoir is exhausted. The
steaming process is interrupted. Check the
water level in the reservoir regularly by referring
to the water level indicator
12
and add more
water in good time.
ATTENTION! HAZARD OF BURNS!
Make sure that the water does not exceed the
MAX mark
19
. Otherwise, hot water may spurt
out of the steamer during operation.
j Press the PROG button
17
to terminate the
delay start. The PROG symbol
21
in the LCD-
display
13
will go out.
Q
Keep-Warm Mode
If the steaming time is elapsed, the appliance will
automatically switch over to keep-warm mode.
- In the LCD-display
13
the time indicator
20
as
well as the keep-warm symbol
22
will appear.
- The pilot lamp
15
will glow green.
- The water is heated repeatedly in cycles in
the warm mode to keep the food warm at a
temperature of approx. 60 - 70°C.
ATTENTION! HAZARD OF BURNS! The
appliance will become hot during use. Beware
of getting in contact with the ascending steam
or any components.
- The keep-warm mode will remain active until
the supply of water is used up or you press a
button.
j Press the ON / OFF button
14
to terminate the
keep-warm mode.
58820_Dampfgarer_Content_LB4.indd 10 11.10.10 10:41
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SDG 800 A1 - 58820 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SDG 800 A1 - 58820 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Silvercrest SDG 800 A1 - 58820

Silvercrest SDG 800 A1 - 58820 User Manual - German, Dutch, French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info