575513

Silvercrest SAS 150 A1 - IAN 46298 Manual

33
Zoom out
Zoom in
Previous page
1/45
Next page
33 GB/MT
Operation
5. The cutting blade
12
continues to rotate for a
short while after the slicer has been switched off.
6. For reasons of safety, the slice thickness must
be returned to the „0“ setting after use.
Soft foodstuffs:
˽ Direct the food carriage
10
slowly against the
cutter
12
. Soft foodstuffs, for example hams or
cheeses, are best cut when they are at a low
temperature / lightly chilled.
Hard foodstuffs:
˽ With hard foodstuffs you can direct the food car-
riage
10
somewhat faster against the cutter
12
.
You can thus quickly prepare your required
amount of of sliced foods, for example salami,
bread or gherkins.
©
Selecting mode of operation
Note:
The two operating modes can be switched on
and off with the rocker switch for intermittent /
continuous operation
3
.
Continuous operation / max. 10 minutes
(switch in position „I“):
˽ Set the switch for intermittent / continuous oper-
ation
3
to position „I“. The cutting blade
12
runs without it being necessary to hold the switch
in this position.
Halting continuous operation: Move the switch
for intermittent / continuous operation
3
into
the „0“ position and wait until the cutting blade
comes to a complete standstill.
Intermittent operation (switch for
intermittent / continuous operation
in position „II“):
˽ Set the switch for intermittent / continuous
operation
3
to position „II“.The cutting blade
will continue to run for as long as the switch
for intermittent / continuous operation is
held in this position. Halting intermittent opera-
tion: Release the switch for intermittent / contin-
uous operation
3
and wait until the cutting
blade comes to a complete standstill.
©
Setting the Vario-switch
cutting blade speed
Low revolutions / Revolution symbol
narrow end:
˽ Set a low revolution speed when you want to
cut soft foodstuffs.Push the Vario-switch
2
completely in the direction of the sharp end.
High revolutions / Revolution symbol
wide end:
˽ Use a high revolution speed for slicing hard
foodstuffs. Push the Vario-switch
2
completely
in the direction of the broad end.
Note: Between the maximum and minimum
adjustments you can naturally also carry out
further individual settings. Practice appropriate
trial slicings.
©
Slice thickness - setting
and cutting
Set the required slice thickness using the control
knob
14
(see Figure C). The settings on the scale
do not correspond with the slice thickness in mm.
For safety reasons the cuttingblade
12
is covered
in setting „0“.
˽ Place the food to be sliced on the food
carriage
10
.
If necessary, press the food to be sliced with
the food holder plate
11
lightly against the
food support
13
.
˽ Switch the appliance on and, whilst lightly
pressing the food to be sliced forward, guide
it along the cutting blade
12
. After using the
slicer always set the food support plate
13
into
the „0“ setting so that the sharp blade is covered.
The cutting blade
12
is ideally suitable for cut-
ting wafer-thin slices of cold cuts or boiled ham
(see Fig. A).
˽ To safeguard your fingers always use the food
carriage
10
and the food holder plate
11
(Ex-
ception: slicing very large pieces of foodstuffs).
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SAS 150 A1 - IAN 46298 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SAS 150 A1 - IAN 46298 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Silvercrest SAS 150 A1 - IAN 46298

Silvercrest SAS 150 A1 - IAN 46298 User Manual - German, Dutch - 36 pages

Silvercrest SAS 150 A1 - IAN 46298 User Manual - Dutch - 9 pages

Silvercrest SAS 150 A1 - IAN 46298 User Manual - French, Italian - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info