749467

Silvercrest IAN 356365 SMA 500 E1 Manual

41
Zoom out
Zoom in
Previous page
1/154
Next page
SilverCrest SMA 500 E1
English - 39
WARNING of damage to property
After cleaning and before using the device again, ensure that the contact area on the
underside of the canister (7) is absolutely dry and free from any detergent residue. If
not, placing the canister (7) on the base (11) can cause a short circuit, which in turn
will result in a defective milk frother.
9. Storing the device when not in use
If the milk frother is not going to be used for a longer period of time, store it in a safe, clean and dry
place.
• Before storing the device, clean it thoroughly as described in the previous section.
• Wrap the power cable (12) around the cable rewind under the base (11) and store the milk
frother in a safe, dust-free place.
10. Troubleshooting
If your milk frother does not work as usual, use the following instructions to try and solve the
problem. If working through the following tips does not eliminate the fault, please contact our
hotline (see the ‘Warranty information’ section).
10.1 The milk frother is not working
• The plug is not inserted. Insert the plug into the power socket.
• The power socket is faulty. Try the milk frother in another power socket that you know definitely
works.
• The milk frother is not switched on. Press the On/Off button (9) to switch on the milk frother.
• The milk frother has overheated and the overheating protection is preventing the device from
switching on. If this is the case, the LEDs of the operating mode symbols (8, 13, 14) will stay
on. Wait until the milk frother has cooled down. Pour milk up to the MIN marking inside the
milk frother to prevent this from happening. Now remove the canister (7) from the base (11) for
a moment.
• The inserted whisk (4,5) does not rotate. The whisk drive axle may be stuck due to milk
residues. Remove the plug and fill the canister (7) with some lukewarm water. Leave the water
in for some time and then try to rotate the whisk drive axle several times with your hand. Pour
out the water. The milk frother should now work again.
10.2 The milk in the canister won’t froth
• Check whether whisk B (5) is inserted. Insert whisk B (5), if necessary.
• Whisk B (5) is not securely in place on the whisk drive shaft. Push
whisk B (5) up to the stop on the whisk drive shaft.
• Please note that the frothing quality depends on the milk used and can vary greatly. See
section “7.5 Tips on how to make good milk froth”.
… 41 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest IAN 356365 SMA 500 E1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest IAN 356365 SMA 500 E1 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info