752633

Silvercrest IAN 316750 KA 6045SCR Manual

17
Zoom out
Zoom in
Previous page
1/61
Next page
17 GB/IE
uninterrupted until it is turned off.
Always keep an eye on the ter-
race heater while it is turned on.
Connect the product in such a
way that the switch and other
controls are out of the reach of
someone in the bath or shower.
Before first use
Check whether the device voltage and the
mains voltage correspond. Operating voltage:
AC 220–240 V 50 Hz
Remove the product and the accessories from
the packaging.
Remove the adhesive label, the protective film
and the plastic packaging from the product.
Installation
Installation with stand
Note: consult the manufacturer‘s operating manual
before using the drill.
Note: for stone patio floors, the included installa-
tion material is suitable for use with dowels 16 or
screws
17
; for wooden floors, only use the screws
17
.
Undo the eight screws 8, 19 .
Remove the base‘s decorative plate 10 .
Select a suitable installation area on the floor,
and mark three holes for the base 10 .
Make 7cm-deep holes in the marked places
using a drill (Ø 8 mm) (see fig. B‒D).
Insert the dowels 16 into the three holes.
Attach the base 10 to the floor using the
screws 17 .
Place the decorative plate back on the base 10
and fasten it using the 4 screws 19 .
Place the lower rod 4c with the flange 9 on
the base 10 , and tighten it with the screws 8.
Place the plastic cover 7 over the connection
between the base 10 and the lower rod 4c .
Note: in the upper rod 4a with the plastic
sheath 3, there is a thin rod with a screw hole.
Pull out the thin rod and screw the fixing screw
15
into the screw hole as far as it will go before
you install the upper rod 4a . This is to guaran-
tee that it does not fall below a total height of
1.80 m (see fig. E).
Place the other two rods 4a , 4b on the lower
rod 4c and tighten them with the screws 6.
Place cable guide clips 5 between each of
them and fasten them using the screws. Make
sure that the upper rod 4a has been installed
with the plastic sheath 3 pointing upwards.
Install the heating unit 1 on the top rod 4a
and tighten the screw.
Pass the cable 13 down through the two cable
guide clips 5 on the rods 4a -4c . The product
is now ready to use.
Important: please make sure that the product
was installed / stands straight. If the product is
not straight, it will not heat up! This is a safety
precaution intended to stop the product emit-
ting heat if it tips over.
Setting the tilt angle
The heating unit 1 does not remain permanently
in the set tilt angle.
Adjust to your desired tilt angle and tighten the
screw on the back of the heating unit 1 (see
fig. F).
Wall mounting
Required tools and materials
The specified tools and materials are not included.
The information and values specified are non-bind-
ing and are only provided as a reference.
The nature of the material is determined by the
specific local conditions.
– Pencil / marking tool
– Cross-tip screwdriver
– Drill
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest IAN 316750 KA 6045SCR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest IAN 316750 KA 6045SCR in the language / languages: English, German, Dutch, French, Polish, Swedish as an attachment in your email.

The manual is 1,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info