753870

Silvercrest IAN 310996 SV 125 A1 Manual

26
Zoom out
Zoom in
Previous page
1/105
Next page
24 GB
3. Place the vacuum bag flat on a level
surface with the valve pointing up-
wards.
4. Proceed as for vacuum containers, start-
ing at step 2 (see “Vacuum containers”
on page 23).
8.3 Filling bags (without
valves)
CAUTION:
~No food or liquids must be present at
the top edge, where you want to seal
the bag. That area must be clean and
dry. Otherwise, it is impossible to pro-
duce a proper welding seam.
• Fill the bag only up to a level of 6 cm
below the top edge.
8.4 Sealing bags (without
valves)
1. Smooth the bag where it is to be
sealed.
2. Open the lid|10. If necessary, press the
buttons|7 first.
3. Place the bag in the device. For this pur-
pose, the end of the film bag must be
positioned just before the rear reference
ridges|11 and the side reference ridg-
es|13.
4. Ensure again that there are no creases
in the film bag - especially in the area
above the welding wire|15.
5. Close the lid|10.
6. Use both hands to press firmly on the
edges of the lid|10. They must audibly
click into place.
7. Press the button |2. The LED lights
up. The film bag is being sealed.
After approx. 5 - 7 seconds, the LED
goes out and the sealing process is com-
pleted.
8. Simultaneously, press buttons|7 in order
to release the lock of the lid|10.
9. Open the lid|10 and remove the bag.
10.Check the welding seam. It should be a
smooth creaseless seam.
8.5 Vacuum-packing and
sealing bags (without
valves)
DANGER! Risk of electric
shock due to moisture!
~For vacuum-packing, no liquids must be
inside the bag.
~Ensure that no liquid is sucked in during
the extraction of air. If this nevertheless
occurs, immediately interrupt the pro-
cess by pressing the active function but-
ton|3 again.
NOTE: when vacuum-packing film bags,
there must not be any vacuum tube|17
plugged into the connection|6.
1. Smooth the bag where it is to be
sealed.
2. Open the lid|10.
3. Place the bag in the device. For this pur-
pose, the end of the film bag must be
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest IAN 310996 SV 125 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest IAN 310996 SV 125 A1 in the language / languages: English, German, Dutch, French, Polish, Swedish as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info