1. Individual response depends on hair type as well as biological factors that may aect hair growth patterns. Some users may respond quicker or slower
than the average number of treatments.
2. One cannot expect permanent epilation in a single or even double treatment sessions. The duration of the resting period for hair follicles also
depends on the body area.
10. How To Use Flash&Go™
10.1. Flash&Go™ Setup
1. Remove the Flash&Go™ hair removal device, and other components from box.
2. Plug the power cord into the Flash&Go™ Device socket.
3. Plug the other end of the power cord into an electrical outlet.
4. All six LED lights will blink on and o, one after the other, in a circle.
Your Flash&Go™ is now ready to start.
10.2. Treating with Flash&Go™ for the first time
1. The skin should be shaved, clean, dry and free of any powders, antiperspirants or deodorants.
2. Press the central button briefly. The Energy level 1 led will turn on.
About 1 second later, the Ready Indicator Light will turn on. The device is now set to deliver the lowest energy
level pulses. The device is ready for you to trigger the first pulse.
3. If you wish to change the energy level, press the CENTRAL BUTTON quickly and repeatedly to increase the
energy level from 1 to 5 and from 5 directly back to 1, cyclically, until the desired energy level is set. The Energy
Level indicator Lights will indicate the energy level setting. (See “Energy Level” frame).
Energy Level
Energy level determines the intensity of the Flash&Go™ light pulse delivered to your skin, from the
lowest level (1) to the highest level (5). Corresponding indicator lights on the control panel represent
the increases in energy. As energy level increases, so do hair removal results as well as the risk of possible
side eects and complications.
Always start your first Flash&Go™ hair removal session at the lowest energy setting.
If you experience little or no discomfort during and after the hair removal session using the lowest energy
level, raise the energy level by one indicator light at the next session, and so on for each subsequent session.
Do not raise the energy level if you experience abnormal discomfort during or after
treating with Flash&Go™ (See section 8 - “Risks of Using Flash&Go™”).
Do not raise the energy level during a hair removal session even if you experience no
discomfort. Discomfort may also appear sometime after the session.
Whenever Flash&Go™ is turned on; its energy level will automatically be reset to the lowest energy level.
Only one Energy Level indicator Light will be on.
To set the energy level, press the central Button repeatedly to increase the energy level. After reaching level
5, an additional press will bring the level back down to Level 1, and so on, cyclically. The number of Energy
Level indicator Lights will coincide with the change in energy level.
4. Apply the TREATMENT SURFACE to the skin, making sure the skin is spread evenly and smoothly and
the TREATMENT SURFACE is in full contact with the skin. Make sure the Ready Indicator Light starts
blinking slowly.
5. Press the Pulse Trigger. The device will first determine the color of your skin.
If the color of the skin is light enough for safe application, the device will flash a pulse of light onto your
skin. You will see a bright flash of light and simultaneously hear a subtle pop sound, which is a normal
noise for the device. You may feel a mild sensation of warmth and tingling.
Flash&Go™ will immediately recharge for the next pulse. After a few seconds (depending on the set
energy level) the Ready Indicator Light will turn on again and start blinking.
If you see no light pulse, and the Ready Indicator Light blinks rapidly, this is now the SKIN COLOR
WARNING INDICATOR LIGHT alerting that your skin tone is too dark for safe application. Try using
the device on a dierent body part or contact Silk’n support.
6. Move the TREATMENT SURFACE to another area of skin.
Administer one pulse at a time at your chosen energy level. Use the pressure marks the device just made in
your skin to guide you for proper positioning of the next pulse, avoiding both gaps and overlaps between pulses.
Flash&Go™ can be applied in two ways: “Pulsing” and “Gliding”.
7. Repeat the process starting again with Step 5.
PULSING
When Pulsing, administer one pulse at a time at your chosen energy level. Use
the pressure marks the device just made in your skin to guide you for proper
positioning of the next pulse, avoiding both gaps and overlaps between pulses.
Covering skin areas
Treatments should be administered in rows, starting at one end of each row and
progressing sequentially towards the other end. This technique allows better
control of skin coverage, and helps you avoid treating the same area more than
once or overlapping skin areas. Ideal body areas for Flash&Go™ use include the
underarms, bikini line, arms and legs and below cheekbones line.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Silkn Flash and Go Compact at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Silkn Flash and Go Compact in the language / languages: English as an attachment in your email.
The manual is 0,8 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
