609114
14
Zoom out
Zoom in
Previous page
1/24
Next page
14
Energy Level
Energy level determines the intensity of the Silk’n SensEpil™ light pulse delivered to your skin, from the lowest level (-)
to the highest level (+). Corresponding
INDICATOR LIGHTS on the CONTROL PANEL represent the increases in energy. As
energy level increases, so does hair removal results as well as the risk of possible side effects and complications.
Always start your first Silk’n SensEpil™ hair removal session at the lowest energy setting.
If you experience little or no discomfort during and after the hair removal session using the lowest energy level, raise
the energy level by one
INDICATOR LIGHT at the next session, and so on for each subsequent session.
10. Remove the APPLICATOR TIP from the treated area of skin.
11. Move the APPLICATOR TIP to another area of skin.
Use the pressure marks the device just made on your skin to guide you for proper positioning of the next pulse, avoiding both gaps
and overlaps between pulses (See “Covering skin areas” frame).
12. Repeat the process starting again with Step 5.
If you see no light pulse and the SKIN TONE WARNING INDICATOR LIGHT blink for 3 seconds, your skin tone, measured by
the
SKIN COLOR SENSOR, is too dark for safe application. Try using the device on a different body part or contact the
Silk’n SensEpil™ support (See: “The Skin Color Sensor” frame)
Warning: Do not treat the same area of skin more than once per hair removal session! Treating the same area of skin
more than once per session increases the likelihood of adverse effects.
10.2. Treating with Silk’n™ SensEpil for the first time
The skin should be shaved, clean, dry and free of any powders, antiperspirants or deodorants.
5. Press the POWER ON/STANDBY SWITCH. The POWER ON INDICATOR LIGHT will turn on and a fan sound (similar to the sound of a
hairdryer) will start.
6. Approximately 3.5 seconds after pressing the
POWER ON/STANDBY SWITCH, the READY INDICATOR LIGHT will turn on and the device
will beep. The device sets itself to deliver the lowest energy level pulses. The device is then ready for you to trigger the first pulse.
7. If the energy level should be higher than the lowest, press the
ENERGY LEVEL SETTING BUTTONS using the “-“ or “+” to respectively
decrease or increase the energy level, until the desired energy level is set.
ENERGY LEVEL INDICATOR LIGHTS will coincide with the
energy level setting. (See “Energy Level” frame).
8. Apply the
APPLICATOR firmly to the skin, making sure the skin is spread evenly and smoothly. Make sure the APPLICATOR TIP is in
full contact with the skin.
9. Press the
PULSE BUTTON. The device will first determine the color of your skin.
If the color of the skin is light enough for safe application, the device will flash a pulse of light onto your skin. You will see a bright
flash of light and simultaneously hear a subtle pop sound, which is a normal noise for the device. You may feel a mild sensation
of warmth and tingling.
Silk’n SensEpil™ will immediately recharge for the next pulse. After 3.5 seconds the
READY INDICATOR LIGHT will turn on again and
the device will beep.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silkn AS101500A SensEpil at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silkn AS101500A SensEpil in the language / languages: English as an attachment in your email.

The manual is 2,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Silkn AS101500A SensEpil

Silkn AS101500A SensEpil User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info