Energy level determines the intensity of the Silk’n™ light pulse delivered to your skin, from the lowest level (-) to the highest level (+).
Corresponding indicAtor lights on the control pAnelrepresent the increases in energy. As energy level increases, so does hair removal results as
well as the risk of possible side effects and complications.
Always start your first Silk’n™ hair removal session at the lowest energy setting.
If you experience little or no discomfort during and after the hair removal session using the lowest energy level, raise the energy level by one
indicAtor light at the next session, and so on for each subsequent session.
Do not raise the energy level if you experience abnormal discomfort during or after treating with Silk'n™! (See section
2.6 - “Possible Side Effects”)
Do not raise the energy level during hair removal session even if you experience no discomfort. Discomfort may also appear
some time after the session.
Whenever Silk’n™ is turned on its energy level will automatically be reset to the lowest energy level. Only one energy levelindicAtor light will be on.
To set the energy level, press the energy level setting bUttonsusing “-“ or “+” to respectively decrease or increase the energy level. The number of
energy levelindicAtor lightswill coincide with the change in energy level.
For your safety, when using Silk’n™ for the very first time, the system is automatically set to deliver the first 50 pulses at the lowest energy level, and
the next 200 pulses at up to level 3.
To cancel these safety settings press and hold the “+” and ”-“ energy level setting bUttons simultaneously until you hear 2 consecutive “beep” sounds.
To restore these safety settings press and hold the “+” and ”-“ energy level setting bUttons simultaneously until you hear 3 consecutive “beep” sounds.
4. Using firm pressure, apply the ApplicAtor tip to the skin. Be sure that the skin area you are about to treat is spread evenly and smoothly, and that the
ApplicAtor tip is in full contact with the skin.
5. Press the pUlse bUtton to emit a pulse. You will then see a flash of light and hear a subtle pop-like sound. This is a normal light pulse of Silk’n™.
Note: As this intense pulse may be disturbing to your eyes, it is recommended to close them shortly before
pressing the pUlse bUtton.
Firmly press the ApplicAtor tip against the skin
6. After emitting a pulse, remove the ApplicAtor tipfrom the skin. Silk’n™ will recharge for the
next pulse.
7. After approx. 3.5 seconds the reAdyindicAtorlight will turn on again, accompanied by a beep, to
indicate that your Silk’n™ is ready for another pulse.
8. Continue to administer pulses until the desired skin area is fully treated.
4.4. Treating with Silk’n™ for the first time
The skin should be shaved, clean, dry and free of any powders, antiperspirants or deodorants.
1. Press the power on/off switch to turn Silk’n™ on.
2. Shortly after pressing the power on/off switch, the reAdy indicAtor light will turn on, accompanied by a beep, to indicate that your Silk’n™ is ready
for its first pulse.
3. Your Silk’n™ is automatically set to the lowest energy level.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Silkn AS101496A at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Silkn AS101496A in the language / languages: English as an attachment in your email.
The manual is 0,79 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
