744789
30
Zoom out
Zoom in
Previous page
1/188
Next page
30
WIDE PANEL
This flashgun is equipped with a built-in wide panel, which can
provide an ultra-wide 17mm angle of coverage. Slide out the
wide panel and catch light panel and flip it down to cover the
flash’s head. (Be careful to slide the panels out smoothly.)
Then put the catch light panel back in its place. P.3-(7)
The Flash head indicating section within the Mode details
area may display the mark when the wide panel is in
use.
BOUNCE FLASH
By firing the flash toward the ceiling or a wall, it is possible to
disperse the light and take pictures with soft light and reduced
shadows.
The flash head can be set to the upper side at 90°, the lower
side at 7°, and the right and left sides at 180°. P.3-(8)
During bouncing, the mark is indicated in the
Status area.
Choose a white surface for bouncing the flash, otherwise the
image’s colour may be incorrect. Depending on the reflecting
surface, the subject distance and other factors, the effective
distance range for TTL AUTO may change.
CLOSE-UP EXPOSURES
By tilting the flash head down to the 7° position, the lower
section of the frame can be bright enough for close-up
exposures.
When it is bounced to the lower side at 7°, the distance
indication in the Status area blinks.
CATCH LIGHT PANEL
This flash is equipped with a built-in catch light panel, which
can create a catch light in the eyes of the subject when the
bounce flash mode is activated. Slide out the wide panel and
catch light panel, then put the wide panel back in its place. (Be
careful to slide the panels out smoothly.) P.3-(9)
To create a catch light effectively, tilt the flash head upward
90 degrees and take pictures at a close distance. P.3-(10)
SYNC.TERMINAL
EF-630 has a synchro terminal that can connect to the camera
by a commercially available flash synchro cable.
When shooting with a synchro cable, use the Flash in
[MANUAL] mode.
With [MENU 2] [ISO] [F-NUMBER], set the ISO and the
aperture (F) value to match that of the camera. Adjust the flash
power output in the Mode details area until the distance
displayed in the Status area is approximately the same as the
distance between the flash and the subject.
Caution!!
S-TTL auto flash does not work if the Sync.Terminal is used.
The EF-630’s Sync.Terminal is compatible with plugs that have
a positive (+) polarity on the central pin and a negative (
-
)
polarity on the shield. If the plug has reverse polarity, use a
commercially-available polarity conversion cord.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sigma EF-630 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sigma EF-630 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 8,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info