630096
18
Zoom out
Zoom in
Previous page
1/40
Next page
en Operating the appliance
18
1. Unfold presorted laundry items and
place them in the drum.
2. Make sure that no items of laundry
are trapped between the door and
the rubber seal, and close the door.
Measuring and adding
detergent and care products
For the majority of programmes on your
appliance, detergent and fabric softener
are dosed automatically; it is a factory
setting for these programmes and can
be changed.
In addition to intelligent dosing, you can
add cleaning aids (e.g. softener, bleach
or stain remover) to the left-hand
compartment , if necessary.
For programmes without intelligent
dosing, or as required (in which case,
set intelligent dosing to "off"), detergent
can be added manually to the left-hand
compartment.
Starting the programme
Touch the I button. The indicator lamp
lights up and the programme starts.
During the programme, the current
programme information is displayed:
Finish in time or, after the washing
programme has started, the
programme duration.
And the displays for the
programme's progress light up
~ Page 10
Note: Foam detection
If the f symbol also lights up on the
Touch-Display, the appliance has
detected too much foam during the
wash cycle and automatically activated
additional rinse cycles to remove the
foam.
Add less detergent to the next washing
cycle with the same load.
If you want to lock the programme to
prevent it from being adjusted
inadvertently, you can select the
childlock ~ Page 18
Childlock
(w 3 sec)
You can lock the appliance to prevent
the functions you have set from being
changed inadvertently in the control
panel.
To activate the childlock:
After the programme starts, touch and
hold the w 3 sec button for approx.
three seconds. The display switches to
full brightness.
If you touch the control panel while the
childlock is actived, the w 3 sec
indicator will flash briefly and a signal
will sound. The programme runs
through to the end unchanged.
Note: When the programme ends, End
is displayed. The door is closed.
w 3 sec indicator still lights up and Œ
symbols remain on to remind you to
deactivate the childlock.
To deactivate the childlock:
Touch and hold the w 3 sec button
until the indicator turns off.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens WM14U640 - Avantgarde iSensoric at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens WM14U640 - Avantgarde iSensoric in the language / languages: English as an attachment in your email.

The manual is 5,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens WM14U640 - Avantgarde iSensoric

Siemens WM14U640 - Avantgarde iSensoric User Manual - German - 40 pages

Siemens WM14U640 - Avantgarde iSensoric User Manual - Dutch - 40 pages

Siemens WM14U640 - Avantgarde iSensoric User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info