473258

Siemens TJ10100 Manual

30
Zoom out
Zoom in
Previous page
1/131
Next page
30
Cleaning and maintenance
Be particularly careful when fitting the
ironing dummy and follow all the
instructions given.
The ironing dummy should only be fitted
when dry.
First fit the airbags:
❏ Each of the airbags (symmetrical) is joined
with a strip. This strip is fitted on the front
between the button band and the support
tubes. The airbag with an extra section with
2 snap fasteners in the middle must be fitted
on the left-hand side of the appliance
(looking head on).
❏ There are three snap fasteners on each side
of the shoulder area which are fitted to the
relevant airbag.
❏ Fit the adjustment cords onto the round
guides around the air-output grille and
secure the cord fixture. Fig. 21.
❏ Position the cross formation on the airbags
and close the snap fasteners on the front at
the bottom. Fig. 22.
The extra section on the bottom left-hand
side must be wrapped around the left-hand
tube, protecting the hole on the tube in this
area.
❏ Check that the adjustment cords are
secured properly.
❏ Check that the airbags are positioned
properly.
❏ Start the “ cold” programme. The
programme can be stopped at any time by
pressing the “start/stop” button.
❏ Check that the airbags are positioned
properly.
❏ Tighten any slack cords.
❏ Correct any problems.
❏ Fit the ironing dummy onto the upper part of
the appliance with the button band still
unlocked and the knob in its vertical
position.
❏ Fit the ironing dummy from back to front.
There are 4 holes on the front of the upper
part of the ironing dummy. The front
adjustment cords are on this section.
❏ When the dummy is fitted, set the knob to
horizontal.
❏ There are two guides on the head: front and
back.
❏ First fit the rear cord and then the front cord
into the guides on the collar and secure.
❏ The ironing dummy is joined to each airbag
via an interior cord. Fig. 23.
❏ Once the inner airbags have been fitted,
turn the sleeves of the ironing dummy
inside out.
❏ Then close the snap fasteners joining the
two parts and turn the sleeve (currently
inside out) outside out again. The arms of
the airbags are now inside the ironing
dummy arms. Fig. 24.
❏ Pull the ironing dummy downwards from the
underarms, Fig. 25. Fit the airbag arms into
the ironing dummy.
❏ Fit the lower adjustment cord on the ironing
dummy into the guide. Make sure that it is
secured properly. Fig. 26.
❏ On the front, the adjustment cord has to be
fitted under the 2 supports on the appliance
on the rear of the button band. Fig. 27.
❏ Tighten the fixture fitting for this cord.
❏ The fixture fitting has to be positioned into
the central rear groove, Fig. 26. Then pull
the adjustment cord again.
❏ Check that all of the adjustment cords are
secured properly.
❏ Close the button band. It clicks into position.
Check that the ironing dummy works properly:
❏ Start the “ cold” programme. The
programme can be stopped at any time by
pressing the “start/stop” button.
❏ Check that the ironing dummy is fitted
properly.
❏ Tighten any slack cords if necessary.
❏ Correct any problems.
❏ Fit the head section into the front guide.
Click the front hook into the hole on the top
part of the head.
❏ Press the head section until it clicks into
position. Fig. 28.
❏ Position each of the cuff adjusters and close
the relevant snap fasteners.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens TJ10100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens TJ10100 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info