649333

Siemens RLM162 Manual

4
Zoom out
Zoom in
Previous page
1/20
Next page
4/20 2015-03-06 CE1G3332xx Siemens Building Technologies
Test mode: (DIP switch no. 5 =
)
Outside temperature compensation, when using an
outside sensor (DIP switch no. 6)
P-band Y1 (potentiometer 5)
Setpoint increase or decrease (slider 3)
4. Replace flexible plastic cover.
5. Switch power on. LED for the operating state must
flash (test mode).
6. First, set temperature setting slider to the minimum
value, then to the maximum value: Actuating device(s)
must travel to the minimum or maximum position.
► If response is wrong, refer to “Troubleshooting”
7. Switch power off.
8. Switch controller to normal operation (DIP switch no. 5
to
).
9. Switch power on. LED for the operating state must
light up (normal operation).
10. If used, activate the auxiliary functions (setpoint
changeover, load-dependent switching contact, etc.).
11. If a remote setting unit is used, set the controller’s
slider for the supply or extract air temperature setpoint
as follows:
To EXT, if setpoint shall be adjusted with the remote
setting unit
To the required setpoint, if the remote setting unit
shall only be used for setpoint readjustments
12. First, set temperature setting slider to the minimum
value, then to the maximum value: Observe the con-
trol. The response may neither be too fast nor too
slow
► If response is wrong, refer to “Troubleshooting”
13. Adjust the setpoint with the temperature setting slider.
14. Replace housing cover.
When used as a supply air temperature limiter
1. Switch on the room or extract air temperature control.
2. Remove housing cover.
3. Lift flexible plastic cover so that you can access the
setting elements.
4. Make the settings:
Operating action: Single-stage heating
Switch no. 1 =
, switch no. 2 =
Control mode: P (switch no. 3 = , switch no. 4 =
)
Test mode: Switch no. 5 =
P-band Y1 on approx. 25 K
5. Replace housing cover.
6. Switch power on. LED for the operating state must
flash (test mode).
7. Set temperature setting slider on the limiter to the
maximum value:
Controller must demand a temperature increase
(heating valve must open or cooling valve must close)
► If response is wrong, refer to “Troubleshooting”
8. Switch power off.
9. Remove housing cover.
10. Switch limiter to normal operation (set switch no. 5 to
).
11. Replace housing cover.
12. Adjust limit value with the temperature setting slider.
Troubleshooting
Wrong response Possible causes
Valve does not re-
spond
Valve not connected
No power supply
Valve travels in the
wrong direction
Selection of operating action is
wrong
Valve remains in one of
the end positions
Temperature setting slider is
set to EXT and there is no
remote setting unit connected
Control responds too
slowly
Reduce P-band
With PI mode, also reduce
the integral action time
Control is instable
Increase P-band
With PI-mode, also increase
the integral action time
fr Français
Montage
Lieu de montage
Comme régulateur de température de reprise :
immédiatement après l'évacuation d'air de la pièce ou
dans la gaine collective dans le cas de plusieurs sorties
d'air. Toujours avant le ventilateur de reprise
Comme régulateur de température de soufflage :
après le ventilateur de soufflage, si celui-ci est placé
après le dernier élément de traitement d'air, sinon
après le dernier élément de traitement d'air à une dis-
tance de 0,5 m
Comme limiteur minimal de la température de soufflage :
le plus près possible de l'arrivée d'air dans le local
Comme régulateur de point de rosée :
immédiatement après le séparateur de gouttelettes du la-
veur d'air
Montage
Procédure :
1. Monter d'abord la bride ; respecter les cotes d'encom-
brement pour le perçage
2. Cambrer la sonde à tige flexible manuellement (ne ja-
mais utiliser un outil) de sorte à ce qu'elle traverse la
gaine en diagonale une fois montée.
Attention La sonde à tige flexible ne doit pas toucher la
paroi de la gaine : distance minimale 50 mm ; rayon de
cambrage minimal admissible = 10 mm
3332Z03
3. Monter la bride de fixation
4. Glisser et encliqueter le régulateur sur la bride de
fixation
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RLM162 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RLM162 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info