Manual Siemens REV24RF (page 8 of 56) (All languages)

620390

Zoom out

Zoom in

1/56

8/56 2015-03-18 CE1G2206xx

Mounting notes REV24RF.. and RCR10/868

1 Placement of units

1.1 REV24RF.. and RCR10/868

· The units must be placed such that transmitted and received signals

will be disturbed as little as possible. For this reason, the following

points must be observed with both the REV24RF.. and RCR10/868:

- Do not mount the units on metal surfaces

- Do not mount the units near electrical wires or electronic equipment

such as PCs, TV sets, microwave equipment, etc.

· Do not mount the units in the vicinity of large metal structures or other

construction elements with fine metal meshes like special glass or

special concrete

· The distance between controller / transmitter and receiver must not

exceed 20 m or 2 floors

1.2 REV24RF.. (controller / transmitter)

· The controller / transmitter should be mounted in the main living room

(wall mounting according to Fig. C, free standing according to Fig. E

with stand)

· The REV24RF.. must be located such that it can acquire the room

temperature as accurately as possible, without getting affected by direct

solar radiation or other heat or refrigeration sources

Wall mounting:

min.

10 cm

2261Z03

1.3 RCR10/868 (receiver)

· The receiver and switching unit should preferably be mounted near the

actuating device

· Make certain that the mounting location is dry and protected from splash

water

· The unit can be fitted to most commercially available recessed conduit

boxes or directly on the wall

2 Checking the wiring

For electrical connections, refer to “Connection diagram”.

Note: Do not use stranded wires, only solid wires

or stranded wires with ferrules!

3 Notes

· The local regulations for electrical installations must be complied with

· If the reference room is equipped with thermostatic radiator valves, they

must be set to their fully open position

· External preliminary protection with max. C 16 A circuit breaker is

required in all cases

· If you wish to check the radio link, press the TEST button at the rear of

the REV24RF..

· LED_1 is lit red if the RCR10/868 receives very weak or corrupted

control telegrams, or no control telegrams at all for about 65 minutes. In

this case, check the display of the REV24RF.. to see if there is an error

message

· As long as the RCR10/868 receives control telegrams, the receiver

works normally. If a control telegram is not correctly received, the relay

will maintain the position assumed last.

As soon as the RCR10/868 receives another correct control telegram

from the REV24RF.., the receiver continues to work normally

· If, for 60 minutes, the RCR10/868 receives no control telegram, or no

correct control telegram, the relay will be deenergized. Hence, the

controlled device is switched off. LED_1 is lit red.

As soon as the RCR10/868 receives another correct control telegram

from the REV24RF.., the receiver continues to work normally

· In the event of a power failure at the RCR10/868, the relay is switched

OFF

· Should the REV24RF.. become faulty, the relay of the RCR10/868 can

be controlled manually. As soon as the REV24RF.. resumes correct

operation, its control telegrams will overwrite the relay’s manual control.

This process can take up to 130 minutes

· Press override button to manually energize and deenergize the

relay. LED_1 indicates manual control by blinking at high frequency.

LED_2 is lit when Lx-L1 is closed (Lx-L2 open). LED_2 is dark when Lx-

L1 is open (Lx-L2 closed)

Commissioning RF set

1 Switching on the REV24RF..

· Remove the black battery transit tab (Fig. F); as soon as the tab is

removed, the unit is ready to operate

2 Selecting the language

· When starting up, the display shows the type of controller at top left and

“THANK YOU …“ in all available languages on the text line

· Press one of the buttons to stop the running display. The choice of

languages starts with “ENGLISH“ (factory setting). Press or

until the language you require appears. Press or move the slider to

confirm the selected language (also refer to Fig. G)

3 Mounting the RCR10/868 temporarily

· If possible, mount the receiver temporarily (e.g. using double-sided

adhesive tape), thus allowing you to find the location with the best

reception conditions

· Wire completely the RCR10/868.

For steps to be followed, refer to Figs. H through M (close the front also)

4 RCR10/868 and REV24RF..

· The units are supplied interconnected

· For manual connection, refer to operating instructions

5 Mounting and setting up the

REV24RF..

· Refer to “Mounting instructions REV24RF.. and RCR10/868“

· Mount or set up the REV24RF.. at your preferred location:

Remove the unit from its baseplate; for procedure, refer to Fig. A

- For wall mounting, refer to Figs. B, C and D

- For setting up, refer to Fig. E

6 Finding the best place for reception

a) Switch on the RCR10/868

b) Set up the REV24RF.. at your preferred location.

Test the radio link by pressing the TEST button at the rear of the controller

(refer to Fig. N1)

c) The display of the REV24RF.. shows the quality of the radio link. The

longer the bar below the numbers 0…9, the better the quality of the radio

link. If the bar only appears below number 0, there is no secure radio link

(refer to operating instructions)

Insufficient Sufficient Good Very good

d) On the receiver, LED_1 indicates the quality of the radio link (refer to Fig.

N2):

Red = insufficient or no connection

Orange = good

Green = very good

e) If the quality of the radio link is insufficient, reduce the distance between

controller and receiver.

Then, repeat the test

7 Mounting the RCR10/868 in its final

place

a) Switch power off

b) Mark the place where the RCR10/868 is located

c) If necessary, remove wiring

d) Mount the receiver at the place previously identified (refer to Figs.

H through M), complete wiring and close the housing

e) Switch power on

how can i take auto off my controls so i can have heating on when i want Submitted on 3-12-2022 at 12:54
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REV24RF in the language / languages: All languages as an attachment in your email.

The manual is 1,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REV24RF

Siemens REV24RF User Manual - English - 2 pages

Siemens REV24RF User Manual - German - 2 pages

Siemens REV24RF User Manual - French - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Siemens REV24RF Manual

Product: