41501
10
Zoom out
Zoom in
Previous page
1/16
Next page
10/16
Siemens Building Technologies Raumtemperaturregler REV23RF CE1N2265en
HVAC Products 20.08.2002
Refer to the Installation Instructions printed on the package.
The receiver must be wired with the power supply switched off.
Mains voltage may be switched on again only after the unit is completely
mounted.
When mounting the unit, the base must first be fitted and wired (L/N = AC 230 V
mains supply, LX/L1 = consumers). Then, engage the unit at the top, swing it down-
ward and secure it with a screw
For more detailed information, refer to the Installation Instructions supplied with the
unit
For the electrical installation, the local safety regulations must be complied with.
It is recommended to first commission and switch on the receiver, then the transmitter.
Switch on mains supply
a) Press the «Reset» button (= delete) for about 3 seconds, LED flashes for about 5
seconds (deleting the stored address)
b) Press «Set» button (= setting / learning) for about 1 second until the LED lights
up
c) The duration of the receiver’s learning readiness is a maximum of 25 minutes.
If no signal is received from the transmitter during that period of time, repeat
steps b) and c)
d) Mount transmitter and put it into operation
e) When the receiver receives a signal from the transmitter, the LED flashes briefly
f) When the LED is steady on, the relay is energized = controlled device ON
g) When the LED is dark, the relay is deenergized = controlled device OFF
h) In the event of a power failure at the receiver, the relay will automatically be de-
energized.
The transmitter repeats the ON or OFF signal at 20-minute intervals, depending
on the operating state. This means that the relay will be energized / deenergized
again after 20 minutes at the latest. This interval was selected to extend battery
life.
If the REV-R.02/1 receives no signal from the controller / transmitter for 60 minutes, the
relay will drop out so that the controlled device will automatically be switched off.
It is recommended to first commission the receiver and then the transmitter.
If the reference room is equipped with thermostatic radiator valves, they must be fully
opened
a) Remove the battery transit tab, which prevents inadvertent operation of the unit
during transport and storage. The unit switches on
b) When – immediately after switching on – symbol
or appears on the
display (controlled device ON), the first signal has already been sent to the re-
ceiver and communication has been opened
c) Make the settings according to the Operating Instructions
d) If symbol
or does not appear on the display (controlled device OFF), it
must first be activated for signal transmission
e) Select operating mode
(comfort mode)
f) On menu T, select the setpoint for comfort mode
g) Use the roller selector to adjust the setpoint to 29 °C and confirm by pressing
h) Heating ON symbol
or appears on the display after a maximum of one
minute
i) The first signal transmission to the receiver has taken place
j) After 10 seconds, the transmitter sends another signal
Support
Mounting and installa-
tion of receiver
REV-R.02/1
Commissioning
Receiver
REV-R.02/1
Commissioning
Controller / transmit-
ter REV23RF
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens REV23RF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REV23RF in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REV23RF

Siemens REV23RF User Manual - Dutch - 15 pages

Siemens REV23RF User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info