Manual Siemens REV16 (page 4 of 18) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish)

41495

Zoom out

Zoom in

1/18

4/18 29.08.2002 CE1G2257xx

Taste hinter der Nadelöffnung zusammen mit der Wärmer-

und Kältertaste mindestens eine Sekunde drücken.

Nach diesem Reset werden die Werkseinstellungen neu

geladen (siehe auch Abschnitt „Werkseinstellungen“ in der

Bedienungsanleitung).

8 Hinweise

• REV16 ist ein elektronischer Raumtemperaturregler mit

Wochenschaltuhr.

• Der Regler gehört zur Softwareklasse A und ist für den

Gebrauch in einer Umgebung mit normalem

Verschmutzungsgrad vorgesehen.

• Sollten im Referenzraum thermostatische

Heizkörperventile installiert sein, müssen diese

vollständig geöffnet werden

• Der Fernbedienungskontakt muss getrennt, d.h. mit

einem separaten, abgeschirmten Kabel verdrahtet

werden

• Die örtlichen Vorschriften für Elektroinstallationen sind

einzuhalten

Commissioning

1 Mounting

Remove controller from its base by proceed according to

Fig. A.

For mounting, refer to Figs. B and C and “Mounting notes“.

2 Check wiring

For the electrical connections, refer to “Connection

diagram“ (also refer to Fig. D).

Note: do not use stranded wires, only solid wires or

stranded wires with ferrules.

3 Remove the battery transit tab

As soon as the battery transit tab is removed, the controller

starts to operate (also refer to Figs. E).

4 Configuration

4.1 Accessing the heating engineer level

The heating engineer level will be enabled by pressing

simultaneously the warmer and colder buttons and by

rolling the roller selector away from the display and then

toward the display (also refer to Fig. G).

4.2 Functions

4.2.1 Calibrating the temperature sensor

After activating the heating engineer level, the CAL symbol

will flash. When pressing the roller selector, the room

temperature currently measured flashes and can now be

recalibrated by a maximum of ± 2 °C by rolling either

toward the display or away from it. To store the re-

calibration, press the roller selector (also refer to Fig.

4.2.2 Setpoint limitation

There are 2 setting choices available:

On the heating engineer level, change from the flashing

CAL symbol to the setpoint limitation symbol by rolling

toward the display. (also refer to Fig.

Press to accept. 5...29 °C will flash (factory setting). Press

to accept or continue rolling.

Setting 16...29 °C will flash.

Press to accept.

4.2.3 Control mode

On the heating engineer level, change from the flashing

CAL symbol to the symbols of the various control modes

by rolling away from the display (also refer to Fig.

Press to accept.

(factory setting) will flash. Press

to accept (Fig. 3) or continue rolling toward the display to

select one of the following control modes:

, PID 6, PID 12 or . Press to accept the

required control mode.

A brief description of the control modes is given below

(also refer to Fig.

Self-learning, adaptive control:

Suited for all standard applications (factory

setting).

PID 12 Normal controlled systems:

For locations with normal temperature variations.

PID 6 Fast controlled systems:

For locations with significant temperature

variations.

Difficult controlled systems:

Proper on / off controller with a switching

differential of 0.5 C.

4.2.4 Periodic pump run

This function protects the pump against seizing during

longer off periods. Periodic pump run is activated for a

minute every 24 hours at 12:00 (when pump run is activa-

ted, the flame symbol

appears on the display).

On the heating engineer level, change from the flashing

CAL symbol to the

symbol by rolling once away from

the display (factory setting, periodic pump run off). Press to

accept.

will flash (factory setting). Press to accept or

continue rolling. The

symbol for periodic pump run on

will flash. Press to accept.

4.2.5 Frost protection mode

Use operating mode selector

to select symbol . If

the standard value of 5 °C need to be changed, the frost

protection setpoint

must be changed via temperature

menu T (refer to the Operating Instructions and also to

Fig.

5 Replacing the controller on its base

Proceed according to Fig. F.

6 Functional check

a) Check the display. If there is no display, check the

correct fitting and function of the batteries.

b) Comfort mode

c) Select temperature menu T and adjust the temperature

setpoint

to 29 °C (refer to the Operating

Instructions)

d) The relay must be energized and thus the actuating

device activated within one minute. Flame symbol

will appear on the display. If that is not the case:

Hi ,
How can we just do an on / off simple setting.. without the 3 times frames and fancy modes. We want to be able to push an on button when we up and an off button whn no longer required. Please help we are freezing!! ; )
Submitted on 9-8-2020 at 01:55
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REV16 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 0,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REV16

Siemens REV16 User Manual - English - 4 pages

Siemens REV16 User Manual - Dutch - 2 pages

Siemens REV16 User Manual - French - 2 pages

Siemens REV16 User Manual - French - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Siemens REV16 Manual

Product: