668967
60
Zoom out
Zoom in
Previous page
1/94
Next page
58
*Do NOT use this function in combination with FDOOT241-9 (ES<13). For detailed
information refer to document A6V10393192.
7.1.2
Output
Configure the output parameters.
Select an output for programming.
Sounder control
Sounder control is used to activate sounder lines.
(EVAC module replaces 'sounder control' with 'EVAC sounder NL'.)
Alarm dialer
Alarm dialer is used to transmit the fire alarm to the intervention
force, e.g. fire brigade.
Fault dialer
Fault dialer is used to transmit the fault signal to the intervention
force, e.g. service provider.
Fire output
Fire outputs are used to activate / deactivate controls,
e.g. door holders, lifts, air-condition, etc.
EVAC Sounder NL
EVAC sounders are used to activate sounder lines.
This option is available if the EVAC module is implemented.
Enables supervision, creeping open and short for the outputs: 4, 5, 8, 9, 12 and 13.
The line calibration is needed to achieve supervision. As a result of the calibration the line
resistance is indicated and can be proved using your own calculation.
This option is only availible on output cards and if supervision is set.
General Alarm
Output is activated if the alarm condition is fulfilled:
Zone 'Direct' is activated, V1 / V2 is expired, cross zoning 2
nd
zone is
activated.
Active by zone alarm Output is activated if the selected zone(s) is in alarm.
General Alert
Output is activated if cross zoning 1
st
zone is in alarm or V1 / V2 time
is running.
Active by zone alert Output is activated if the selected zone(s) is in alarm by cross zoning
1
st
zone or V1 / V2 time is running.
Alert by ext. input
Output is activated if one input is activated and programmed as
'activate alert mode'.
Any isolation
Output is activated if any isolation is set.
Any fault Output is activated if any fault condition occurs.
Manned mode
activated
Output is activated if manned mode is activated.
Alarm dialer fault
Output is activated if the alarm dialer fault via input is
in fault condition.
Dialer device
confirmation signal
Output is activated if the programmed input is activated.
V1 / V2 is running
(SE function)
Output flash during V1; Output on during V2.
Activation
condition
*
Calibrate
line
S
upervision
EN 54-13
Mode
Output
1..n
Output
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens FC123-ZA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens FC123-ZA in the language / languages: English as an attachment in your email.

The manual is 3,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info