555852
5
Zoom out
Zoom in
Previous page
1/8
Next page
5/8
Siemens Building Technologies Installation guide CA2Z3884en
Building Automation 08.2001
2 AC 230 V supply cables
Sizing and fuse protection of the supply cables depends on the total load and on local
regulations. The supply cables must be secured with cable restraints.
3 AC 24 V transformer sizing
The DESIGO RXA controllers have an AC 230 V supply voltage. They generate the
AC 24 V supply for the connected field devices.
The power amplifiers for the UA1T thermic valve actuators have an AC 24 V supply and
require a transformer. This transformer must satisfy the requirements specified in
EN 60742 for SELV low voltage.
The transformer sizing is based on the total power consumption of all connected
devices (for UA1T, refer to data sheet CA2N3591). The transformer secondary winding
must be fused.
4 Signal cables
The following applies to the signal cables of field devices such as temperature sensors,
room units, window switches, occupancy sensors, dew point sensors and electric
switches:
- Use twisted, 2-core or multi-core round cable without a screen (standard
installation cable)
- Single conductors and ribbon cable must not be used
- Signal conductors may be routed together with mains cables (AC 230 V), but they
MUST be insulated from the mains in accordance with regulations and in
compliance with SELV requirements.
- Signal conductors must
NOTberoutedinthesamecable
as mains conductors.
Cable length and other specifications are as follows:
- Max. length of single cable: 100 m
- L&S Ni1000 sensors must not share ground conductors (source of measurement
errors)
- Recommended cable cross-section: A 1mm
2
Max. length of single conductor with diameter 0.6 mm: 100 m
The same ground conductors may be used for more than one signal input.
- Max. length of single conductor where A 1.0 mm
2
: 125 m (and see table)
- Cable type: 2-core, twisted pair, unscreened
A Diameter Max. length of single cable
[mm
2
][mm] [m]
1.00 1.15 125
0.75 0.98 115
0.50 0.80 75
Measured value input B1
(L&S Ni1000 sensor)
Signal inputs D…
Room unit
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens DESIGO RXA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens DESIGO RXA in the language / languages: English as an attachment in your email.

The manual is 0,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info