459227
26
Zoom out
Zoom in
Previous page
1/63
Next page
ENGLISH
26
When selecting the “D.VOL (Dolby Volume)”
• Dolby Volume is an intelligent system that improves the perceived audio frequency response at lower listening levels and
corrects for volume inconsistencies between sources (e.g. a jazz radio station and a DVD) and between programming (e. g. a
TV show and advertisement breaks).
OFF (Default value) : To turn off the Dolby Volume function. (The DOLBY VOLUME indicator goes off.)
ON : To turn it on. (The DOLBY VOLUME indicator lights up.)
• If the Dolby Volume is set to ON, it will be automatically turns on the Volume Modeler that maintains the same perceived
listening experience as the reference level experience.
Note :
• If the Dolby Volume is changed to OFF, the volume level may be increased high.
When the Dolby Volume is set to ON
. Press the ENTER button to enter the Dolby Volume setup.
• Then “LVL (Volume Leveler)” is displayed for several seconds.
. Press the CURSOR UP/DOWN buttons to select the desired parameter.
• Each time these buttons are pressed, the parameter mode changes as follows :
“LVL” “AMOUNT”
(Volume Leveler) (Volume Leveler Amount Control)
“C/O” M/S HALF
(Calibration Offset) (Mid/Side mode) (Half mode)
. Press the CURSOR LEFT/RIGHT buttons to adjust the selected parameter as desired.
When selecting the “LVL” (Volume Leveler)
• The Volume Leveler maintains the perceived loudness of all content for example, from different channels or input sources.
OFF : To turn off the Volume Leveler function.
ON (default value) : To turn it on.
Note :
• If Volume Leveler is turned off, no level matching between sources and program material is performed. This is not the same as
turning Dolby Volume off as volume related frequency response processing is still active.
When selecting the “AMOUNT” (Volume Leveler Amount Control)
The Volume Leveler Amount adjusts the amount of leveling applied by the Volume Leveler.
• The control can be set in 11 steps from 0 to 10 (default value : 9)
When selecting the “HALF” (Half mode)
If the Half mode is set to ON, the Volume Modeler does not apply volume contour gains for playback levels higher than reference
level; just the volume setting, as a flat spectrum gain, is applied.
OFF (default value) : To turn off the Half mode.
ON : To turn it on.
When selecting the “M/S” (Mid/Side mode)
The Mid/Side processing can improve stability of some stereo material.
OFF (default value) : To turn off the Mid/Side mode.
ON : To turn it on.
When selecting the “C/O” (Calibration Offset)
The Calibration Offset allows you to compensate for speaker efficiencies and listening position.
• The control can be set from -15 to +15 dB (default value : 0 dB) and this should normally produce a good result when you set
the speaker levels on this receiver using a SPL (Sound Pressure Level) meter.
Continued
R-904N(A)_ENG_091007:R-904N(A) 2009-10-14 오후 1:53 페이지 26
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sherwood R-904N NetBoxx at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sherwood R-904N NetBoxx in the language / languages: English as an attachment in your email.

The manual is 3,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info