469885
82
Zoom out
Zoom in
Previous page
1/86
Next page
-80
CheckProblem Page
An unusual sound is
occasionally heard
from the cabinet.
Maintenance
indicator illuminates or
blinks in red.
The projector cannot be
turned on or put into the
standby mode using the
ON or STANDBY button
on the projector.
All buttons on the
projector and the remote
control are unavailable.
Picture is green on
COMPUTER 1or 2
(COMPONENT).
Picture is pink (no green)
on COMPUTER 1/ 2 or
DVI (RGB).
The black levels of the
image show banding or
appear faded when DVI
or HDMI is selected.
Picture is too bright and
whitish.
The cooling fan
becomes noisy.
The lamp does not light
up even after the
projector turns on.
The lamp suddenly turns
off during projection.
The image sometimes
flickers.
The lamps take a long
time to turn on.
Picture is dark.
The remote control
cannot be used.
If the picture is normal, the sound is due to cabinet shrinkage
caused by room temperature changes. This will not affect
operation or performance.
See “Maintenance Indicators”.
If the “Keylock Level” menu is set to “Level A” or “Level B”, all or
specific buttons on the projector are unavailable. Use the
remote control to operate the projector.
If the “Stack Setting” menu is set to “Slave” and the “Keylock
Level” menu is set to “Level B”, all buttons on the projector and
the remote control are unavailable. Connect the remote control
to the projector, and then use the remote control to operate the
projector.
Change the input signal type setting.
Make adjustments that result in the best picture quality in the
“Dynamic Range” setting.
Image adjustments are incorrectly set.
When temperature inside the projector increases, the cooling
fan runs faster.
The lamp indicator is illuminating in red.
Replace the lamp.
Cables are incorrectly connected to the projector or the
connected equipment works improperly.
If this happens frequently, replace the lamp.
The lamps will eventually need to be changed.
The lamps have reached the end of its life. Replace the lamps.
Operate the remote control while pointing it at the projector’s
remote control sensor.
The remote control may be too far away from the projector.
If direct sunlight or a strong fluorescent light is shining on the
projector’s remote control sensor, place the projector where it
will not be affected by strong light.
Is a ø3.5 mm minijack cable plugged into the WIRED REMOTE
terminal?
The batteries may be depleted or inserted incorrectly. Make
sure the batteries are inserted correctly or insert new ones.
69
63
17
62
63
51
51
49
9, 10
66, 69, 70
69
2427
72
72
16
16
This projector is equipped with a microprocessor. Its performance could be adversely affected by incorrect op-
eration or interference. If this should happen, unplug the projector and plug it in again after more than 5 minutes.
Troubleshooting
82


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp XG-P610X-N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp XG-P610X-N in the language / languages: English as an attachment in your email.

The manual is 7,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp XG-P610X-N

Sharp XG-P610X-N Quick start guide - English - 59 pages

Sharp XG-P610X-N User Manual - Dutch - 86 pages

Sharp XG-P610X-N User Manual - Dutch - 59 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info