13339
58
Zoom out
Zoom in
Previous page
1/63
Next page
E57
EnglishDeutschFrançaisItalianoEspañolEnglish
Instructions for attaching a VESA-compliant mount
An arm or stand based on the VESA standard
(commercially available) can be attached to the TV.
Procurement of the arm or stand is at the
customer's discretion.
Arms or stands able to be used
Attachments must satisfy the following.
- Compatible with the VESA standard.
- The six screw holes on the section to be
attached have a gap of 100 mm between them.
- Not be likely to fall off or break off after being
attached to the TV.
How to attach the arm or stand
- Be careful not to over bend the cable or add
extension cords as this could lead to a
malfunction.
- While following these instructions, please also
refer to the installation instructions in the
operation manual included with the arm or
stand.
CAUTION!
- Be careful not to get your fingers pinched
between the display and stand nor to let the
stand drop. These could lead to injury.
- Do not cover or block the vents and openings
since insufficient ventilation can cause
overheating.
1.Remove the cables.
2.Spread out a soft cloth on a flat surface. Being
careful not to damage the TV, gently lay the TV
on it display-side down.
3.Remove the two screws and then remove the
rear cover of the stand.
4.Remove the six screws and then remove the
stand from the TV.
Notes:
- The stand is specially made for use with this
TV. Once having removed the stand, never
attempt to attach it to another equipment.
- Once having removed the screws, store them
together with the stand. If the stand is ever re-
attached, be sure to use the original screws.
Using different screws could lead to a
malfunction.
5.Attach the arm to the TV with the six screws.
Note:
- The screws used to attach the arm should be
M4 screws with a length of 6 mm - 8 mm
protruding from the surface to be attached.
Using different screws could cause the TV to
fall off or to be internally damaged.
6.Reconnect the cables.
Screw used to attach arm
Arm
Part of TV to which arm is
attached
6 mm - 8 mm
LD-23SH1U_gb_02.P65 2005/01/20, 20:2357
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp LD-23SH1U Operation Manual at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp LD-23SH1U Operation Manual in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info