138269
97
Zoom out
Zoom in
Previous page
1/102
Next page
97www.sharp.co.uk/support
DVD
Problem
The DVD player is switched on but
does not operate.
The playback image does not
appear.
No sound is produced.
The sound is not Dolby Digital (5ch
or 5.1ch).
The image and sound are garbled.
The sound is not stable during
playback.
Suggested Solution
Have you loaded a disc?
Is the disc unplayable? (See pages 9 – 11.)
Is there dew in the DVD player? (See page 11.)
Are the video and audio cables connected correctly? (See pages
18 – 23.)
Is the disc scratched? (See page 11.)
Is the disc dirty? (See page 11.)
Is the disc loaded upside down?
Is the input selector on the TV set to “VIDEO” or “AV”?
Is the audio equipment switched on and are all the components
connected properly? (Refer to the operation manuals for your
audio equipment.)
Is the disc you are playing recorded in Dolby Digital (5ch or
5.1ch)?
Have you set the DIGITAL” in “AUDIO SETUP” to
“BITSTREAM”? (See page 45.)
Is the disc scratched? (See page 11.)
Are vibrations from the speakers affecting the DVD player?
Set the “COMPRESSION” in “AUDIO SETUP” to “OFF” (See page
45.)
This unit is equipped with a microprocessor. Its performance could be adversely affected by external electrical
noise or interference. If this should happen, unplug the Unit and plug it in again after a few minutes.
Troubleshooting
Possible Cause/Solutions
The record-protection tab has been removed from the cassette.
Broadcast does not carry VPS/PDC signal which alters recording
time.
Check VPS/PDC mode is switched ON.
Ensure date and time are correctly set on the Unit.
Make sure there is no other tape in the VCR.
Make sure you are loading the tape correctly.
Make sure the tape is not at the start.
The channel position has been set to be skipped. Cancel the SKIP
mode for that channel.
Make sure all the cables are connected properly.
Make sure the VCR power cord is properly plugged in.
Possible weak signal strength, the same channel with a better
signal strength may have been tuned in on another VCR preset
channel. Example; VCR preset 1 = BBC1 and VCR preset 14 =
BBC1 (Refer to Manually Sorting Channels section to move the
channel to your desired position.)
TV aerial may need adjusting.
Problem
Tape is automatically ejected when
pressing
ÆÆ
ÆÆ
ÆREC or TIMER ON/OFF.
VIDEO Plus+ does not record
desired programme.
Tape can not be loaded.
Rewind is not possible.
Desired channel position can not be
selected.
No colour or poor TV picture on
normal viewing.
Desired channel has interference.
OTHER
INFORMATION
DVNC65H096_101.pm6 30/8/02, 12:11 pm97
97


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp dv nc 65 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp dv nc 65 in the language / languages: English as an attachment in your email.

The manual is 16,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp dv nc 65

Sharp dv nc 65 User Manual - Dutch - 99 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info