576369

Shark MV3010 Rotator Professional Manual

11
Zoom out
Zoom in
Previous page
1/20
Next page
7
www.sharkclean.com
Occasionally the vacuum may become blocked
by a build up of debris and the Blockage
Indicator light will illuminate. It is important
to locate where the blockage is and carefully
remove it without causing damage to yourself,
the unit or anything else. Perform the
following steps to try to find the blockage.
Beware of sharp objects when clearing blockages.
Damages caused while clearing or attempting to clear
blockages are not covered under your product’s limited
warranty.
Replace parts securely before using again.
Blockages may cause your vacuum to overheat and
shut down. If so, clear the blockages, then follow the
instructions for Resetting the Motor Thermostat.
CHECKING FOR BLOCKAGES
Dust Cup Air Duct:
1 Remove Dust Cup Assembly and empty Dust Cup
if necessary.
2 Check Air Duct behind Dust Cup for clogs; clear
before replacing Dust Cup Assembly.
(Fig. 20)
CLEANING THE VACUUM NOZZLE:
The rotating brush in the vacuum nozzle
must be free of debris for effective cleaning
and maximum suction.
1 Disconnect the vacuum nozzle and turn it
over to inspect the bottom. If a build-up of
debris is wound around the rotating brush,
remove by carefully cutting with scissors.
Avoid damaging or cutting the bristles.
(Fig. 21)
Air Intake
Fig. 20
Fig. 21
Vacuum Mode: Storage
1 Tilt the cleaning unit back into upright position.
2 Tap the foot pedal until the unit returns to standby
mode. The carpet light (on the left hand side of the
nozzle) should be blinking blue. (Fig. 22)
3 Unplug the unit.
4 Wrap cord around cord holders and secure plug. Store
cleaning unit in an upright position. (Fig. 23)
Fig. 22
Fig. 23
TO RESET THE MOTOR THERMOSTAT:
1 Step on the foot pedal until it goes to standby mode.
2 Unplug the vacuum.
3 Empty the dust cup and clean filters.
4 Check for blockages in hose, accessories and inlet
openings.
5 Allow the unit to cool for a minimum of 45 minutes.
Note: If vacuum still does not start, contact Customer Service
at:
1-800-798-7398.
MV3010_40_ENG_IB_120713_2.indd 7 12-07-13 1:36 PM
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Shark MV3010 Rotator Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Shark MV3010 Rotator Professional in the language / languages: English as an attachment in your email.

The manual is 3,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info