576369

Shark MV3010 Rotator Professional Manual

10
Zoom out
Zoom in
Previous page
1/20
Next page
6
TOLL FREE: 1-800-798-7398
NOTE: The material in the filters will discolor over time. This is NORMAL and will not affect the performance of the filters.
DO NOT operate the vacuum without ALL the filters in place.
DO NOT operate the vacuum with WET filters.
Always unplug the vacuum from the electrical outlet before doing any maintenance on the appliance.
Vacuum Mode - cont.
TO CLEAN THE POST-MOTOR HEPA FILTER
1 To release the vacuum nozzle, press the top
“nozzle release” button first and then lift up on
the main body. (Fig. 17)
2 Lift the HEPA filter out from the vacuum nozzle.
(Fig. 18)
3 Thoroughly rinse the filter in lukewarm water.
(Fig. 19) Air dry for 24 hours before reusing.
DO NOT use a hair dryer or any other forced
hot air to dry the filter.
4 Once it is thoroughly dry, replace the HEPA filter
into the vacuum nozzle.
NOTE: Any other servicing should be performed
by an authorized service representative.
TO CLEAN THE PRE-MOTOR FILTERS
1 Press the dust cup release button on the top
of the unit. Pull the dust cup out of the unit by
pulling forward on the handle.
2 Remove the two foam filters from the unit.
(Fig. 15)
3 Thoroughly rinse the two filters in lukewarm
water. Squeeze out any excess water. (Fig. 16)
Air dry for 24 hours before reusing.
DO NOT use a hair dryer or any other forced
hot air to dry the filter.
4 Insert a dry filter set into the unit. The order of
the filters impacts your dust cup performance.
Make sure the thick filter is on the top and the
thin filter is on the bottom.
Fig. 15
Pre-Motor Filters
Thick Foam
Thin Foam
COMPONENT
MAINTENANCE SCHEDULE
Rinse and air dry every month under normal use.
Empty each time you vacuum.
Pre-Motor Foam Filters
Dust Cup
Clean once every 12 months under normal use.
Post-Motor HEPA Filter
1
2
3
Post Motor Filter
Hepa Filter
Fig. 18
Fig. 19
Fig. 16
Fig. 17
MV3010_40_ENG_IB_120713_2.indd 6 12-07-13 1:36 PM
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Shark MV3010 Rotator Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Shark MV3010 Rotator Professional in the language / languages: English as an attachment in your email.

The manual is 3,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info