556603
19
Zoom out
Zoom in
Previous page
1/52
Next page
So that the doors can close tightly against the frame, take the utmost care that they are properly
aligned during re-assembly.
Open the freezer door (18).
Remove the fixing screws (1 and 3) from
the top cover (two screws at the front and
two at the rear), and take off the cover
(4).
Unscrew the upper hinge bracket (5) and
remove it. Caution: the door must be
supported while this is done.
Take off the freezer door (18).
Unscrew the hinge pin (7) together with
the nut (6) and washers (8), and fit the
entire assembly to the opposite side of the
hinge bracket.
Undo the fixing screws (11) on the centre
hinge bracket (10).
Caution: Support the door.
Take off the centre hinge bracket (10)
together with the hinge pin washers and
the plastic plate (9).
Take off the refrigerator door (13).
Tilt the whole unit towards the rear.
Unscrew the lower hinge bracket (14)
and take it off.
Unscrew the hinge pin (15) from the
bracket, and re-insert it from the other
side.
Remove both screws on the left of the
underside and replace them on the right.
Fit the lower hinge bracket (14) on the
left of the underside.
Put the washers on the hinge pin.
Remove the cap (19) from the freezer
door and the cap (16) from the refrigerator door and replace them on the opposite side of the
doors.
Take off the caps (17) from the partition between the refrigerator and freezer compartments and
remove the screws.
Replace both screws on the opposite side and then the caps.
Fit the refrigerator door (13) onto the pin (15) of the lower hinge bracket.
Fit the pin of the centre hinge bracket (10), together with the washers, to the refrigerator door
(13).
Fit the centre hinge bracket (10) together with the plastic plate (9).
Remove both screws from the upper left and replace them on the right.
Place the freezer door (18) onto the pin of the centre hinge bracket.
Fit the pin of the upper hinge bracket (5) to the freezer door (18), and then fit and secure the
upper hinge bracket (5).
Note: If necessary, the alignment of the doors can be adjusted by slightly loosening the hinge bracket
19
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Severin KS 9762 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Severin KS 9762 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info