Manual Severin KS 9703 (page 19 of 124) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Finnish)

712682

Zoom out

Zoom in

1/124

Problem Possible cause and solution

The appliance is not working at all. ∙ The temperature control is set to ‘0’.  Use a higher temperature setting.

∙ The wall socket is defective.  Check the fuse. If necessary, have the wall outlet

checked by a qualiﬁ ed electrician.

The temperature inside the refrigerator

cabinet or freezer compartment is not

low enough.

∙ Too much food has been stored in the appliance.  Do not store excessive food (see

product data sheet).

∙ The doors are not properly closed.  Ensure that the doors are properly closed.

∙ The door seals are defective.  Check the door seals and contact our Customer

Service if necessary.

∙ There is too much dust on the condenser.  Clean the condenser regularly.

∙ Insufﬁ cient ventilation: the unit is too close to a wall or other structure or object. 

see section ‘Ventilation’.

∙ The temperature control is set too low.  Use a higher setting.

The normal operating sound changes

or becomes louder.

∙ The unit is not ﬁ rmly set on the ﬂ oor.  Use the adjustable front feet to align the unit

properly.

∙ Adjacent furniture or objects are affected by the running of the cooling unit (i.e. causing

them to vibrate).  Keep the stated clearances.

∙ Any objects on top of the unit might be vibrating  Remove such objects.

Water is collecting on the bottom of

the unit.

∙ The melt-water drain system is blocked.  Remove the blockage and clean the

system.

Excessive build-up of frost on the rear

of the main cabinet.

∙ Hot food has been stored inside the cabinet.  Let the food cool down before putting

it in.

∙ The door seals are defective.  Check the door seals and contact our Customer

Service, if necessary.

∙

The temperature control is set too high.  Use a lower temperature setting.

Excessive build-up of frost inside the

freezer compartment.

∙ It is necessary to de-frost the freezer compartment manually

.  See ‘De-frosting and

cleaning’

∙ See ‘Excessive build-up of frost on the rear of the main cabinet‘ (above).

Reversible door

∙ If required, the door may be reversed, i.e. from right-hinged

(default installation) to left.

∙ To avoid the risk of personal injury or damage to the unit,

two people are needed to reverse the door.

∙ Warning: Always disconnect the unit from the mains before

any maintenance or repair work is carried out.

∙ Before you start, please note the following:

∙ Always ensure that the correct number of washers is used

on all hinge bolts and screws.

∙ So that the doors can close tightly against the frame, take

the utmost care that they are properly aligned during re-

assembly.

1. Remove the four covers C from the housing and inside of

the door.

2. Unscrew the hinge bolt on the inside of the door in the

area C/6. Caution: Support the door.

3. Take off the refrigerator door.

4. Take out the ﬁ xing screws and remove the upper bracket

6. Note the small plastic plate underneath the bracket.

5. Turn the bracket 6 including the small plastic plate through

180° and replace it on the other side of the refrigerator,

using the two screw holes adjacent to each other.

6. Place the refrigerator door on a soft surface. Remove the

hinge support 5 from the underside of the door and ﬁ t the

hinge support provided on the opposite side.

7. Take out the covering caps and then remove the hinge

support in the middle 4. Note the small plastic plate

underneath the bracket. Caution: Support the door.

8. Take off the freezer door 3.

9. Remove the lower panel 1 by lifting it up slightly.

10. Take out the ﬁ xing screws and remove the bracket 2 with

its hinge bolt. Note the small plastic plate underneath the

bracket.

11. Unscrew the hinge bolt, together with the washers, from

the bracket, and ﬁ t it into the corresponding opening on

the opposite side of the bracket.

12. Remove the bracket 7 and replace it with the holding

bracket 2 with its hinge bolt.

13. Now install the holding bracket 7 in the previous position

of the bracket 2.

14.

Take out the sealing plugs 8

from the partition separating

the refrigeration and freezer compartments and replace

them in the openings on the opposite side.

15. Take out sealing plugs 9 from the freezer door and replace

it in the opening on the opposite side.

16. Place the freezer door onto the hinge bolt on holding

bracket 2. Caution: Support the door.

17. Turn the holding bracket 4 with its hinge bolt and plastic

plate through 180°.

18. Replace the bracket bolt on the opposite side of the

freezer door and secure it with the screws.

19. Replace the covering caps over the screw heads.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Severin KS 9703 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 0,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Severin KS 9703 Manual

Product: