Manual Severin KB 8871 (page 13 of 88) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Finnish)

761655

Zoom out

Zoom in

1/88

142 x 208 mm

Before using for the rst time

∙ Remove any exterior and interior packaging materials

completely, including the adhesive strips.

∙ Please ensure proper disposal of all packaging

materials.

∙ Before it is connected to the mains, the unit must be

thoroughly checked for transport damage, including its

power cord.

∙ Clean the unit as described in the section De-frosting

and cleaning.

∙ The unit should only be transported in its vertical

position; do not tilt any more than 30°.

∙ Once the unit has been positioned, wait for about 30

minutes before it is connected to the mains.

∙ If the unit has been tilted more than 30° during transport,

allow it to stand upright for at least 4 hours before it is

connected to the mains.

∙ When the unit is rst switched on, a slight ‘new’ smell

may be noticed. However, this will disappear once the

cooling process has begun.

Installation

∙ The appliance should be set up in a well-ventilated, dry

room.

∙ It should be operated in conditions where the relative

humidity is no more than 70 %.

∙ The product data sheet at the end of this manual

contains details of the ambient temperature range

suitable for this appliance.

∙ Do not use the appliance outdoors.

∙ Ensure that the plug is accessible and can be removed

from the wall socket at any time.

∙ Do not expose the appliance to direct sunlight, and

do not position it next to any heat sources (radiators,

cookers etc). If this cannot be avoided, however, a

suitable insulation must be in installed between the heat

source and the unit.

∙ The unit must not be installed inside a cabinet, nor

directly below a hanging cupboard, shelf or similar

object .

∙ Do not place any objects on top of the unit, and do not

otherwise cover it.

∙ If the oor is uneven, the height-adjustable feet at the

front of the unit can be used to compensate and ensure

optimum stability.

Ventilation

Ensure that there is enough space around the unit so that

the air circulation round and behind it is not obstructed.

(Rear 7.5 cm, sides 5 cm, top 10 cm.)

Reversible door

If required, the door may be reversed, i.e. from right-hinged

(default installation) to left-hinged.

Warning: Always disconnect the unit from the mains

before any maintenance or repair work is carried out.

1. Remove the upper hinge blind cover.

2. Use a suitable socket spanner to remove the three

screws holding the upper hinge to the housing, and

then lift off the hinge.

3. Carefully lift up the door and place it on a soft surface

to protect it from scratches.

4. Remove the three blind covers for the hinge mounting

holes on the opposite side and t them in the

corresponding place on the other side. Ensure that the

cover are rmly pushed down into the holes.

5. Remove the adjustable feet.

6. Remove the two screws on the lower hinge plate and

take the plate off.

7. Remove the hinge-pin from the hinge plate, turn the

plate through 180° and put back the hinge-pin.

8. Install the hinge plate with the hinge pin facing up

on the other side. Caution: Do not yet tighten the

screws.

9. Replace and tighten the adjustable feet.

10. Replace the door in its new position. Ensure that the

hinge pin is inserted into the guide bushing (hole) on

the lower part of the door.

11. Install the upper hinge on the closed door. Ensure that

the hinge pin is inserted into the guide bushing (hole)

on the upper part of the door. Caution: Do not yet

tighten the screws.

12. Adjust the closed door to its proper position and

tighten the screws of the upper and lower hinge plates.

13. Replace the hinge cover on the upper hinge.

14. Put the unit back in its intended position and wait for

about four hours before connecting it to the mains.

Temperature control

The unit is activated by connecting it to the mains. It is only

switched off completely when the plug is removed from the

wall socket.

The temperature in the refrigerator cabinet can be adjusted

by setting the temperature control.

Turning the control clockwise will decrease the

temperature, while turning it anti-clockwise will increase it.

We recommend turning the temperature control initially

to a medium setting. After a certain time, the actual

temperature should then be checked with a thermometer,

and adjustments made if necessary.

Following a power interruption, or if the unit has been

switched off on purpose, it may take 3 to 5 minutes before

it switches on again.

Note: In position ‘0’, the cooling function is switched

off, though the appliance is still connected to the

mains.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Severin KB 8871 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 0,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Severin KB 8871 Manual

Product: