651323

Sentry EF3428E - Executive Fire-Safe Manual

4
Zoom out
Zoom in
Previous page
1/12
Next page
4
3-Number Combination Lock
and Dual Combination Key Lock
NOTE: See the sticker on the back cover of
this manual for your combination.
IMPORTANT: The lock on this safe is
in the open position. DO NOT operate
the combination until first reading and
understanding the following instructions.
Test first
WITH DOOR OPEN!
Test your combination several times
with the door open.
To unlock and open
Before dialing your combination, simply insert the
key (if equipped) in the lock and turn clockwise.
1. Start the dial at ZERO.
2. Turn the dial to the left. Make sure ZERO
passes the pointer at least THREE times. Then
stop at the first number of your combination.
3. Turn the dial to the right. Stop the
SECOND time you reach the second number of
your combination.
4. Turn the dial to the left. Stop the FIRST
time the pointer reaches the third number of your
combination.
To Close and Lock
With the door closed, turn the handle
counterclockwise to secure the locking bolts, then
spin the combination dial to the left at least four
times to scramble the combination.
Standard Electronic Lock and
Dual Electronic Key Lock
To activate lock:
Four alkaline AA batteries, Voltage: 6Vdc, (not
included) are required to activate the keypad.
NOTE: Non-alkaline and rechargeable
batteries ARE NOT RECOMMENDED.
To install batteries:
1. Using two
hands, hold the
keypad, thumbs
down, on its
left and right
sides. Push up
the keypad with
your thumbs,
and disconnect it
from the safe by
pulling it towards
you. (Fig. A)
2. Let the
disengaged
keypad hang by
its wires. This will expose the battery holder.
(Fig. B)
3. Install four alkaline AA batteries as illustrated on
the back of the battery holder.
4. Reconnect the keypad by inserting the keypad’s
four posts into the matching holes.
5. Push down to snap into place.
Test first
WITH DOOR OPEN!
(See back cover of this manual for your
factory code.)
Test your factory code several times with the door
open.
NOTE: Only a light touch is needed. A green
PROCEED light and a single beep indicate
that the keypad “felt” your touch. The
lock allows 5 seconds for each key press.
If you pause longer, an error signal will
occur (blinking red light and three beeps),
indicating you should start over.
For safes with dual combination key lock insert key
and turn clockwise.
1. Press the 5-digit factory code. The green light
will come on.
2. Turn the handle clockwise and open the door.
Access codes
There are three possible ways to unlock and
access the safe—by entering its preset Factory
Code, your own User Code or a User PIN (Personal
Identification Number).
You can always open the safe by entering the
5-digit Factory Code. This code cannot be deleted.
But if you prefer to use your own code, you can
program the safe to open to the 5-digit User Code
of your choice. If you wish to give someone else
temporary access to the safe, you can program a
User PIN that can later be erased.
Programming a user code
There are two ways to program a user code.
A 1. Press the Program key. (Prog.)
2. Enter the Factory Code. The green LED remains
ON while you enter the 5-digit user code of your
choice. After 5 digits are entered the green LED
turns OFF.
(To enter a new User Code, repeat these steps.)
B 1. Press the red button on inside of door (hinge
side). The lock will “beep” and the green LED will
come on.
2. Enter a 5-digit user code.
(To enter a new User Code, repeat these steps.)
Keep your new user code secure
For your records, please copy it here:
_____ _____ _____ _____ _____
Programming a user PIN
1. Press the Program key.
2. Press it a second time.
3. Enter your 5-digit User Code. The green LED
remains ON.
4. Enter the 5-digit User PIN of your choice (any
combination except 00000.) After 5 digits are
entered, the green LED turns OFF.
(To enter a new User PIN, repeat these steps. To
erase the User PIN, press Program twice, enter your
User Code and then enter 00000.)
Key override
If your electronic lock fails or you do not have any
codes available, you may use a key override to
access this unit.
1. Using two hands, hold the keypad, thumbs
down, on its left and right sides. Push up the
keypad with your thumbs, disconnect and remove
the battery holder.
2. Insert the skeleton key into the key hole inside
the opening for the battery.
3. Turn the key to the right.
4. Open the door.
Lock instructions
1
Gaining Entry into Safes with Combination Locks
2
Gaining Entry into Safes with Electronic Locks
A
B
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sentry EF3428E - Executive Fire-Safe at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sentry EF3428E - Executive Fire-Safe in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info