Manual Sencor SVC 1035 (page 5 of 6) (English)

759450

Zoom out

Zoom in

1/6

- 5 - 09/2020

EN Bagless vacuum cleaner

User'smanual

DESCRIPTION OF THE VACUUM CLEANER

A1 Cord winding button

A2 On/Off button

A3 Suction power control knob

A4 PUSH button (serves to release the

dust container)

A5 Rubber coated wheels

A6 Dust container lid

A7 Dust container

A8 Hose connection hole

A9 Handle

A10 Sliding flap for air suction

A11 Telescopic tube

A12 Telescopic tube position lock

A13 Combination floor nozzle

A14 Flap position for vacuuming carpets

A15 Flap position for vacuuming hard

(smooth) floors

A16 Hose

A17 Accessory holder

A18 Stopper for the horizontal and

vertical parking position

A19 Clip

A20 Hose end

A21 Front travel wheel

A22 Vertical parking position

A23 Power cord

A24 Inflow filter

A25 Foam pre-filter

A26 Horizontal parking position

A27 Outflow filter

A28 Outflow filter protective grille

A29 Long flexible crevice nozzle

A30 Crevice nozzle

A31 Upholstery nozzle

A32 Brush attachment (easy to attach

to the upholstery nozzle for gentle

vacuuming of fine upholstered

surfaces)

ASSEMBLY

Inserting the hose into the air suction hole on the vacuum cleaner.

■ Press both the clips on the end of the hose A20 and insert it into the air suction hole

A8 on the vacuum cleaner until you hear a"click". The hose A16 is now secured in

the correct position.

Attach the holder to the telescopic tube:

■ Make sure to place the holder with the hose on the wider part of the telescopic

tube A11.

Attach the floor nozzle to the telescopic tube:

■ Make sure that the floor nozzle A13 is attached to the narrower part of the

telescopic tube A11.

Adjust the length of the telescopic tube:

■ Adjust the length of the telescopic tube A11 as required – disengage and hold the

clip A19 on the tube in the direction shown by the arrow and adjust the length

of the tube A11 as required. Then release the clip A19 and slide out the tube A11

slightly forward until you hear a"click". The telescopic tube A11 is now securely

locked in position.

USING THE VACUUM CLEANER

Connecting the vacuum cleaner to the power grid

■ Wind out the required length of the power cord by pulling on the power plug. Insert

the power plug into apower socket.

Attention:

The yellow marking on the power cord warns you that the power

cord is close to its end. Do not pull the cord farther than the red

marking.

Adjusting the floor inlet nozzle according to the floor surface.

■ You may set the inlet nozzle according to the floor surface by adjusting the inlet flap:

- If you want to vacuum carpets, move the flap to retract the bristles.

- If you want to vacuum hard and smooth surfaces, move the flap to extend the

bristles.

Turning your vacuum cleaner on and off

■ To turn on the vacuum cleaner, press the On/Off button A2. To turn off the vacuum

cleaner, press the button A2 again.

Adjusting the suction power

■ Suction can be controlled using the control knob A3. Turning clockwise (towards

MAX) increases the power of the vacuum cleaner, turning anticlockwise (towards

MIN) reduces the power. In asmaller range, you may regulate suction power using

the mechanically sliding flap A10 on the hose handle.

TIPS

■ Use the maximum suction power when vacuuming carpets or floors with ahard

surface. Use the reduced strength when vacuuming upholstery, window curtains,

etc.

■ If the hose holder becomes blocked when vacuuming, disconnect it from the

telescopic tube and also disconnect the hose from the vacuum cleaner body.

Then place the holder inside the suction hole on the vacuum cleaner body and

vacuum the stuck dirt out.

Temporary interruption of the vacuuming process

■ If you wish to interrupt vacuuming for awhile, you can use the horizontal A26 or

vertical A22 parking position on the vacuum cleaner, into which you insert the

stopper A18 on the floor nozzle.

Attention:

Do not move the vacuum cleaner from place to place if the hose

is in the parked position! The stopper on the floor nozzle could

brake off.

Ending the vacuuming process

■ When you finish vacuuming, switch the vacuum cleaner off by pressing the On/Off

button A2 and then disconnect the power cord plug from the power socket.

■ To wind the power cord back into the vacuum cleaner, press and hold the winding

button A1 with one hand and guide the power cord with the other.

TIP:

■ If the winding process stops and part of the power cord is still outside, release the

winding button A1 and pull the cable out again by about 50 cm and then press

and hold the winding button A1 again and repeat the winding process.

USING THE ACCESSORIES

■ The combination floor nozzle A13 for hard floors ensures perfect and yet gentle

vacuuming of smooth hard surfaces thanks to the brush being from 100 % natural

bristles. It can be used to vacuum floors that are sensitive to scratching such as

wooden or floating floors, marble floors, tiles, linoleum, etc.

■ The long flexible crevice nozzle A29 serves to vacuum very hard-to-reach places

anywhere in your car.

■ The crevice nozzle A30 is suitable for vacuuming hard to reach places (e.g. window

frames, libraries, upholstery corners, joints, etc.).

TIP:

■ If during vacuuming you use an accessory very often, you may attach it to the

special holder on the telescopic tube.

CLEANING AND MAINTENANCE

Attention:

Before cleaning, disconnect this appliance from the power source.

Emptying the dust container

■ Empty the dust container A7 as soon as it fills up to the MAX mark; otherwise the

air flow and the suction power will be reduced. Nevertheless, it is recommended to

always empty out the dust container when you have finished vacuuming.

1. Take out the hose A16.

2. Press the PUSH A4 button and pull out the dust container A7 upwards.

3. Remove the lid of the container A6 and take out the dust filter. Tip the dust out of it

and rinse it out under lukewarm running water if necessary.

4. Take the dust container A7 above awaste bin and turn it upside down to shake the

dirt and dust out of it. If it is heavily soiled you may wash the entire container under

running lukewarm water. It is, however, necessary to first remove the inflow filter

A24 and its foam pre-filter A25 before doing this!

5. Insert the dust filter into the dust container A7 and put on the lid A6.

6. Insert the container A7 into the vacuum cleaner.

Attention:

Make sure that all parts are completely dry before reinserting

the dust container A7 and the dust filter back into the vacuum

cleaner.

Replacing and cleaning the inflow filter and the foam pre-filter

1. Press the PUSH A4 button and pull out the dust container A7 upwards.

2. Fold out both safety clips of the inflow filter frame A24, take it out of the dust

container A7 and from behind it also remove the foam pre-filter A25.

3. Wash both filters under running lukewarm water and if necessary replace with new

ones.

4. Then first reinsert the foam pre-filter A25 and then the inflow filter A24 until you

hear both clips click in.

5. Place the dust container A7 back into the vacuum cleaner.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SVC 1035 in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SVC 1035 Manual

Product: