Manual Sencor SDH 3020 (page 11 of 13) (English)

759179

Zoom out

Zoom in

1/13

Automatic defrosting

In the event that frost forms around the vaporizer coil, the appliance will automatically

switch to the automatic defrost mode until it eliminates the frost. In this mode, the

compressor will turn on in regular intervals and the fan will run continuously. Indicator

light B13 will be lit on the control panel A2.

DRAINING CONDENSATE

For the purpose of draining condensate you can use the condensate tank A3, drain hose

outlet A6 or the pump drain hose outlet A8.

Draining condensate into the tank

Prior to turning on the appliance, check that outlets A6 and A8 are fitted with plugs.

During operation, condensate will accumulate in the tank A3. As soon as it fills up, the

indicator light B12 will be lit and the appliance will turn off automatically. Error message

"P2" will appear on the display B9.

Carefully slide out the condensate tank A3, careful not to spill any water. The bottom

of the condensate tank A3 is not level, therefore do not stand it on the floor when the

condensate tank A3 is full. Empty out the condensate tank A3 and insert it back into

the appliance. Check that the condensate tank A3 is correctly installed. The appliance

will automatically resume operation.

When removing the condensate tank A3, be careful so as not to drop it and damage the

internal parts of the appliance. Do not use excessive force when installing the condensate

tank A3 into the appliance. Using brute force may damage the appliance.

If the hose falls out while removing the condensate tank A3, it is necessary to put it back

in its place before inserting the condensate tank A3 into the appliance.

If there is any water in the installation area of the condensate tank A3, wipe it using

adry wiping cloth.

If you remove the condensate tank A3 while the appliance is running, the compressor

and the fan will stop, abeep will be made and the error message "Eb" will appear on

the display A9.

If you remove the condensate tank A3 while the appliance is turned off, abeep will be

made and the error message "Eb" will appear on the display A9.

Continuous condensate draining via the drain hose

For continuous draining of condensate, screw off the plastic plug anticlockwise from

the drain hose outlet A6. Carefully store the plug for future use.

Note:

If there is water in the outlet when the plug is removed, wipe it using adry

wiping cloth.

Properly screw in the threaded end of the drain hose A6 to the outlet. To ensure that

condensate does not leak, check that the hose end is properly screwed in.

Locate the free end of the hose so that the condensate can flow out freely. The container

or place where the condensate is drained must be lower than the outlet A6. Do not

bend or twist the hose.

Set the required humidity and fan speed to start the appliance.

Note:

When not using the drain hose for continuous draining of condensate, screw

off the hose, wipe away nay water and close the outlet A6 using the plug.

Draining condensate using apump

Screw the plug out of the pump drain hose outlet A8. Check that aplug is installed in

outlet A6. Insert the pump drain hose at least 15mm deep into outlet A8. To ensure that

condensate does not leak, check that the hose end is properly screwed in.

Locate the free end of the hose so that the condensate can flow out freely. The container

or place where the condensate is drained must be lower than the outlet A8. Do not

bend or twist the hose.

Press button PUMP B1 to activate the draining of condensate using apump.

Condensate will be fed into the condensate tank A3, and once the condensate tank A3

is full the pump will automatically be started, which will drain the condensate from the

condensate tank A3 out of the appliance.

Note:

You may hear anoise while the pump starts up. This is normal. The pump will

run for approximately 3 – 5minutes.

If the indicator light above button PUMP B1 starts flashing, then amalfunction with

the pumping out of the condensate has occurred. Turn off the appliance using button

B8 and disconnect the power cord from the power socket. Check the following points:

- Check that the pump filter is clean.

- Remove the condensate tank A3 out of the appliance, remove the pump and clean

out the filter.

- Check that the pump hose is not twisted or bent.

- Empty out the condensate tank A3.

- Screw out and reattach the pump drain hose. Remove and reinstall the condensate

tank A3. Turn on the appliance and if the problem persists, please contact an

authorised service centre.

Note:

Do not run the appliance in this mode at atemperature of 0°Cor less.

Otherwise frost may form inside the appliance, condensate my freeze in the

drain hose and the appliance may subsequently be damaged.

In this condensate draining mode, it is important to pour condensate out of the

condensate tank A3 at least once per week.

When not using the pump drain hose to drain the condensate, carefully remove the

hose from the outlet A8 and close the outlet A8 using the plug. Be careful not to spill

water from the drain hose on to the floor.

CLEANING AND MAINTENANCE

Disconnect the power plug from the power socket before cleaning.

Note:

For cleaning, do not use cleaning products with an abrasive effect, solvents,

etc. that could damage the appliance.

Warning:

To prevent the risk of injury by electrical shock, do not submerge

the appliance, power cord or power plug in water or another liquid.

Cleaning the condensate tank

Empty out the condensate tank A3 whenever you finish using the appliance and wipe

it using awiping cloth.

To prevent undesirable bacteria, micro-organism or moulds from multiplying inside

the tank A3, clean it out at least once per month using acloth dampened in lukewarm

water with the addition of neutral detergent. Then rinse it out thoroughly using clean

water, wipe it dry and insert it back into the appliance.

Do not wash the tank A3 in adishwasher.

Cleaning the air filter

After approximately 250hours of operation, the indicator light above button FILTER B3

will be lit, signalling that the filter requires cleaning.

Release the grille A11 and then carefully remove the filters A10. Wash the filter A10

in warm water with asmall amount of kitchen detergent. Then thoroughly rinse it

under running water and allow it to dry naturally. Install the filter A10 back in its place.

However, first make sure that the filter A10 is completely dry. Then reattach the grille A11.

Warning:

Do not use the appliance without the filter A10 being properly

installed. Never wash the filter A10 in adishwasher.

Cleaning the outer cover and air outlet grilles

To clean the air outlet grille A11 and the outer cover, use awiping cloth lightly dampened

in lukewarm water with asmall addition of neutral detergent. Make sure that water

does not enter into the vents. In the event that the grille A11 is only dusty, avacuum

cleaner may be used to clean it.

Storage

When not using the appliance for an extended period of time, disconnect the power

plug from the power socket and clean it according to the instructions provided above.

Clean the condensate tank A3 only 24hours after turning the appliance off since even

during this time asmall amount of condensate may accumulate.

Wind the power cord around the holder.

Store the appliance in adry, clean and well-ventilated location not exposed to extreme

temperatures and out of children'sreach.

TROUBLESHOOTING

Problem Solution

The dehumidifier

cannot be turned on.

Check that the power cord plug is correctly connected to

apower socket.

Check that fuses are in order.

The dehumidifier reached the set humidity level or the

condensate tank A3 is full.

The condensate tank A3 is not correctly installed.

The dehumidifier is not

removing humidity

from the room.

The dehumidifier has only been running for ashort time,

please wait afew more moments.

Make sure that there are no curtains, roller blinds or

furniture in front of the dehumidifier.

The humidity setting is insufficient.

Check that the doors, windows and other openings in the

room are properly closed.

The temperature in the room is too low (below 5°C).

There is an appliance located in the room that may be

creating humidity.

The dehumidifier is too

noisy while running.

The air filter is clogged.

The dehumidifier is tilted.

The floor is not level.

Frost is forming inside

the appliance.

The dehumidifier is equipped with an automatic defrost

function, which is activated when frost starts to form.

There is water on the

floor.

Check the hose for damage and that it is correctly

attached.

Disconnect the hose and use the condensate tank A3 to

drain the condensate. Close outlets A6 andA8 using plugs.

Indicator light above

PUMP B1 is flashing.

Clean out the pump filter.

Check that the drain hose is not crimped of clogged.

Empty out the condensate tank A3.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SDH 3020 in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SDH 3020 Manual

Product: