528684
10
Zoom out
Zoom in
Previous page
1/16
Next page
Wire
d Measurement using Flash Unit
with Synchro Cord
Wired measurement is recommendable when you measure the flash light
from the subject position, or when the meter fails to register flash light in
wireless (cordless) measurement; for example, close to a fluorescent lamp,
or in high ambient condition, and so forth.
(2) Set the film speed (ISO) and shutter
speed (T) as shown in the
paragraphs for “Preparing the Meter
for Operation”.
(3) Connect the synchro cord to the
synchro terminal of meter and the
flash unit.
(4) Point the Lumisphare accurately
toward the camera from the subject
position, and press the measuring
switch to fire the flash.
(5) The appropriate F-stop value is
displayed on the meter (Fig. 18).
For repeat measurement, press
the measuring switch again.
< NOTE >
The notes for wireless measurement
are also applicable to wired
measurement.
16
Cumulative Measurement using
Electronic Flash Unit
When you are unable to obtain sufficient illumination with a single flash or
you try for special effects using a multiple exposure technique, there may be
cases that you wish to use your flash repeatedly. In such cases, you should
set the meter to the cumulative measurement mode. Cumulative
measurement is usable for both wireless (cordless) and wired
measurements for flash light.
(1) Before pressing the measuring
switch, set the cumulative
measurement mode by pressing the
multi-measurement key. The symbol
of MO is indicated on the display
(Fig. 19).
(2) Measure the flash light as shown in
the paragraphs for “Wireless
(cordless) Measurement using
Electronic Flash Unit” or “Wired
Measurement using Flash Unit with
Synchro Cord”.
(3) The reading and the number of
cumulative frequency are displayed
automatically each time the flash is
fired (Fig. 20). The maximum
possible cumulative flashes is 9. If
the flash is fired 10 or more times,
the number of cumulative flashes is
replaced by E mark (Error) and no
further reading is possible (Fig. 21).
(4) To repeat the cumulative
measurement, press the multi
measurement key once to release
the current reading. And press the
multi key again to prepare the fresh
reading.
In case of wireless (cordless)
measurement, pressing the
measuring switch can also release
the current reading.
<NOTE>
Memory display function (refer to
page 20) is not usable if the meter is
used in the cumulative
measurement mode.
17
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sekonic L-718 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sekonic L-718 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info