491192

SEG Utah Manual

43
Zoom out
Zoom in
Previous page
1/111
Next page
11
Utah 81cm LED BLU-TV
EN
Basic Operation
QUICK START GUIDE
Connection
1. Connecting the mains and antenna.
2. If TV has a power switch, turn it on rstly. Then press
Power button on the remote to turn on the TV.
• Initial Setup
When the TV is initially powered on (Or no preset chan-
nels), a sequence of on-screen prompts will assist in
conguring basic settings.
1. Select a language
Press the▲/▼/◄/►button, then press the ENTER but-
ton.
Select the desired OSD (On Screen Display) language.
2. Select the appropriate country
Press the▲/▼/◄/►button to select the country.
Then press the ENTER button.
3. Select the picture mode.
Press the▲/▼button to select the picture mode.
4. Select an antenna source
Press the▲/▼button, then press the ENTER button.
When selecting Air
Press the ▲/▼/◄/►button to select the appropriate
country and tune type, then press the ENTER button.
The TV starts Auto tuning.
When selecting Cable
A step appears allowing you to set parameters to the
channels. For more information, refer to Channel
(Auto Tuning).
Press the
▲/▼/◄/► button to select the appropriate
country and tune type, then press the ENTER button.
The TV starts Auto tuning.
When selecting Satellite
Press the▲/▼/◄/►button to select the appropriate
country, then press the ENTER button.
A step appears allowing you to set parameters of the
Satellite. For more information, refer to Channel (Auto
Tuning).
When setting is completed, press the blue button to
enter the Channel Tuning menu. Select the ENTER
button to start Auto tuning.
Turning on and off the TV
• Turn on the TV
Connect the AC input cable then turn on the power switch
of the TV. At this time the TV will enter standby mode.
Press the button on remote control can turn on TV from
standby mode.
• Turn off the TV
Press the button on the remote control to enter standby
mode.
Do not leave your set in standby mode for long periods
of time. It is best to unplug the set from the mains and
aerial.
• No signal
There is No Signal menu on screen when there is no input
signal. In TV/DTV mode, if there is no signal in fteen
minutes, the TV will turn off automatically. In PC mode,
the TV set will automatically turn off in ve minutes if no
input signal. When VGA cable is connected, the TV turns
on automatically.
Programme Selection
• Using the CH+/CH- on the panel of TV or on the remote
control.
Press CH+ to increase channel number.
Press CH - to decrease channel number.
• Using 0- 9 digital buttons.
You can select the channel number by pressing 0 to 9. (In
TV, DTV mode)
• Example
To select - channel (e.g. Channel 5): Press 5.
To select -- channel (e.g. Channel 20): Press 2 and 0 in a
short time.
Volume adjustment
• Press the VOL+/- button to adjust the volume.
• If you want to switch the sound OFF, press the .
• You can release mute by pressing the or increase/de-
crease the volume.
Changing the Input Source
You can select the input source by pressing the SOURCE
button on the remote control. Press the ▲/▼ button to
cycle through the input source, and press the ENTER but-
ton to conrm your choice.
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for SEG Utah at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of SEG Utah in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 17,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info