664164
20
Zoom out
Zoom in
Previous page
1/33
Next page
ENGLISHENGLISH
39 |
KIDS’ TOY BICYCLE | OWNER’S MANUAL 2017OWNER’S MANUAL 2017 | KIDS’ TOY BICYCLE
| 38
b ca e fd
To make sure the inner tube does not get pinched between the rim and the
bead, move the tyre sideways back and forth between the sides of the rim.
While doing so, also check whether the rim tape has shifted.
Inflate the inner tube to the desired pressure. The maximum pressure is indicat-
ed on the side of the tyre (a).
Check whether the tyre is properly seated by inspecting the fine witness line
just above the rim edge. This line should be even to the rim all around the tyre.
Starting from the maximum tyre pressure you can now reduce the pressure
through the valve to suit your needs. Please observe the recommended tyre
pressure range.
REMOUNTING THE WHEEL
Mounting the wheel is done in the reverse order of dismounting. Make sure the
wheel is correctly seated in the drop-outs and accurately centred between the
fork legs or the seat and chainstays. Make sure the drop-out safety tabs are
correctly seated.
In the case of back-pedal brakes check the proper assembly of the individual
components and tension the chain before tightening the wheel nuts by pulling
the wheel backwards. Make sure there is not more than two centimetres of play
midway between sprockets and chainring. Make sure there is no excessive chain
slack!
Pull the brake lever (b) after you have mounted the wheel. To do so, lift the
bicycle off the ground and spin the wheel with your hand. The rim must keep off
the brake pads.
DANGER!
G
If you have rim brakes, make sure you hook up the brake cable immediately
after the wheel mounting (c)! Make sure the brake keeps clear of the rim,
the tyre or the spokes, when spinning the wheel.
DANGER!
G
Retighten the torque support (d) in the case of back-pedal brakes.
DANGER!
G
Before setting off again, check that the brake surfaces are still free of
grease or other lubricants after the wheel mounting.
DANGER!
G
Check whether the brake pads hit the rotors or brake surfaces of the rims.
Make sure the wheel is properly seated and firmly fixed in the drop-outs.
Always do a brake test as described in the chapter “Tests before every ride“!
HEADSET
The headset connects the fork to the frame, but allows it to move freely. It
must turn with virtually no resistance if the SCOTT toy bicycle is to run straight,
stabilising itself as it travels. Shocks caused by uneven road surfaces expose the
headset to considerable levels of stress. In this way, it can become loose and go
out of correct adjustment.
DANGER!
G
Riding with a loose headset on the toy bicycle increases the stress on fork
and bearings. The fork can break. Risk of an accident!
CHECKING AND READJUSTING
Check the headset for play by placing your fingers around the lower head tube
race (e).
Bring your weight to bear on the saddle, pull the front brakes with your other
hand and push the SCOTT toy bicycle firmly back and forth with the wheel
remaining on the ground (f). If the bearing has play, you will feel the upper head
tube race moving in jerks relative to the lower head tube race - visible as a small
gap in between the head tube races.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scott Toy Bike - 2016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scott Toy Bike - 2016 in the language / languages: English as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scott Toy Bike - 2016

Scott Toy Bike - 2016 User Manual - German - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info