664181
9
Zoom out
Zoom in
Previous page
1/15
Next page
16
SPARK | BIKE OWNER’S MANUAL 2015 BIKE OWNER’S MANUAL 2015 | SPARK
17
ENGLISH
ENGLISH
SAG
The SAG should be 10mm on the shock piston.
To check the adjustment, please follow the below instructions:
1. Sit on the bike, put your feet on the pedals
2. Put your feet back on the ground and stand over the bike without bouncing the
bike during this action
3. Check if the o-ring (S9) on the shock piston (S8) has a distance of 10mm to the
main dust wiper/seal between shock housing and piston.
- if the distance between the o-ring and the main dust wiper/seal is 10mm, the air
pressure is correct for your weight
- if the distance between the o-ring and the main dust wiper/seal is less than 10mm,
the air pressure of the air chamber is too high and should be carefully reduced by
using the bleed knob of the shock pump until the distance is 10mm.
- if the distance between the main dust wiper/seal is greater than 10mm, the air
pressure of the air chamber is too low and should be increased by using the shock
pump until the distance is 10mm.
SET-UP OF REBOUND FOX NUDE OR FOX CTD SHOCK
Rebound” describes the speed the shock comes back to its original length after
absorbing an obstacle.
By using the rebound adjuster knob (S4) you can adjust the rebound step by step.
Please refer to the following instruction:
Ride your bike off a pavement (remain in the saddle) and check how many times it
bounces.
- If it bounces 1-2 times, the set up is good.
- If it bounces more than 3 times the rebound is too fast. Turn the knob 1-2 “clicks
clockwise
- If it does not bounce the rebound is too slow. Turn the knob 1-2 “clicks” counter
clockwise.
IMPORTANT!
Note that you have to mount the FOX Nude Shock always as shown below.
Mounting the rear shock in a different position can cause severe damage to the
frame, the linkage levers and the rear shock.
Same for the FOX Float CTD and X-Fusion E1 shock on some of the Spark models.
IMPORTANT!
After a dismantlement of the rear shock, both fixing bolts should be tightened with a
tightening torque of 10Nm/88in-lbs.
If this is not done correctly the rear shock can be damaged.
Please only use SCOTT shock bolts and follow the assembly instructions
shown below:
Please only use the matching adjustment
shims as their shape is designed specifically
to fit with the countersunk bolts.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scott Spark - 2014 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scott Spark - 2014 in the language / languages: English as an attachment in your email.

The manual is 3,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scott Spark - 2014

Scott Spark - 2014 User Manual - German - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info