780001
7
Zoom out
Zoom in
Previous page
1/13
Next page
12 PLASMA 5 | BIKE OWNER’S MANUAL 2015 BIKE OWNER’S MANUAL 2015 | PLASMA 5 13
ENGLISH
ENGLISH
FORK
Setup screw:
front end height can be set to adjust the front wheel tire clearance with the frame
thanks to the fork dropout screws M5 (511). The fork (200) length can be set from
370mm to 380mm.
- Loosen the screws to set a higher front end
- Tighten the screws to set a lower front end.
Make sure right and left side are set at the same length by assembling the front
wheel and verifying it is centred with the fork crown.
Drop out adjustment screws: Standard M5*10mm headless screw available in any
hardware shop.
IMPORTANT
Make sure the inner diameter bearing chamfer is positioned onto the fork bearing
seat cone, place the stem (301A/B) into the frame headtube cut-out, place the fork
(201) into the headtube, push the fork (201) from below so that the steerer tube goes
through the stem 1” hole.
Put the upper 1” bearing (902) into the headtube upper bearing seat on top of the
headtube
IMPORTANT
Put the upper 1” bearing (902) into the headtube upper bearing seat on top of the
headtube, make sure the outer diameter bearing chamfer is positioned upon the
headtube bearing seat chamfer.
IMPORTANT
Put the 1” compression ring (903) on the steerer tube, make sure the compression
ring chamfer is positioned onto the 1” upper bearing inner diameter chamfer (face
down), put the top cap (904) on the top of the headset and tighten the M6 screw
(907) to the specified torque (T17), place the two M5 screws (303) into the recesses
located at the rear end of the stem body (301A/B), slide the stem on the steerer tube
to achieve its correct positioning, and make sure it does not touch the frame at any
point, tighten up the screws (907) to the specified torques (T1).
Once the cable routing is done, place the headtube cap (905) on the top of the
headtube and tighten the M4 screw (906) to the specified torque (T18).
Headset compression kit SCOTT part number: 239282
Headset Syncros Drop-In 1” - 1 1/8SCOTT part number: 238601
HEADSET/STEM BODY TT5
Headset/Stem body assembly:
put the compression kit (908) into the steerer tube and tighten the bolt to the
specified torque (T16) , position the lower 1”1/8 bearing (901) onto the fork (201)
bearing seat
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scott Plasma 5 - 2019 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scott Plasma 5 - 2019 in the language / languages: English as an attachment in your email.

The manual is 3.05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scott Plasma 5 - 2019

Scott Plasma 5 - 2019 User Manual - German - 13 pages

Scott Plasma 5 - 2019 User Manual - French - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info