664134
6
Zoom out
Zoom in
Previous page
1/13
Next page
ENGLISHENGLISH
CABLE ROUTING: FOR MECHANICAL SHIFTING
Rear Derailleur (RD) Cable Housing:
IMPORTANT
To avoid any damage to the frame structure put a housing end plug at the end of
the housing.
Place the RD cable housing into the headtube long hole, push the housing until it
touches the rear end of the headtube (you may feel a resistance), orient the housing
up and push the housing again, it will then follow the headtube down and continue
its travel along the downtube, continue running the cable housing into the frame until
it is visible from the bottom bracket opening.
Route a derailleur cable into the right dropout exit hole until it is visible from the
bottom bracket opening, feed the cable into the cable housing and lead the housing
to the right chainstay inner structure, pull the housing along the cable until it shows
from the right dropout exit hole, leave approx. 150mm of cable housing outside
the frame.
Rear Brake (RB) & Front Derailleur (FD) Cable Housings:
IMPORTANT
To avoid any damage to the frame structure put a housing end plug at the end of
the housing.
Place the housing into the headtube long hole: RDhousing=left/
RBhousing=middle/ FDhousing=right, push the housing until it touches the
rear end of the headtube (you may feel a resistance), direct the housing up and
push the housing again, it will then follow the headtube down and continue its
travel along the downtube.
Continue running the cable housing into the frame, once the housing is visible from
the bottom bracket opening, lead the housing to the bottom bracket exit hole on
the underside of the downtube in front of the bottom bracket, pull the housing to
leave approx. 100mm of cable housing outside the frame.
Front Brake (FB) Cable Housing:
refer to the Stem/Handlebar section.
Front derailleur cable guide:
IMPORTANT
for mechanical shifting only
position the front derailleur housing into the cable guide cavity, bend the housing
and position the cable guide pin into the corresponding positioning hole on the low
side of the bottom bracket, place the M4 sunk head screw into the cable guide recess
hole, tighten up the screw at the specified torque.
Front derailleur cable exit:
route the front derailleur wire/liner through the frame front derailleur exit hole, put
the wire/liner into the cable exit rubber part slot, slide the cable exit rubber part
along the wire/liner, plug the cable exit part into the frame exit hole.
Front derailleur BB cable guide (801) SCOTT Part number: 239181
11 |
BIKE USER MANUAL | PLASMA 5PLASMA 5 | BIKE USER MANUAL
| 10
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scott Plasma 5 - 2017 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scott Plasma 5 - 2017 in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scott Plasma 5 - 2017

Scott Plasma 5 - 2017 User Manual - German - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info