779976

Scott MTB E-bike 2018 Manual

19
Zoom out
Zoom in
Previous page
1/33
Next page
ENGLISHENGLISH 37 |
KIDS’ TOY BICYCLE | OWNER’S MANUAL 2017OWNER’S MANUAL 2017 | KIDS’ TOY BICYCLE
| 36
b ca e fd
Tyre removal
Remove the cap and the fastening nut off the valve and deflate the tyre com-
pletely (a). Press one tyre side from the rim sides towards the centre of the rim
(b). This will ease the removal.
Apply a plastic tyre lever to one bead of the tyre about 5 cm beside the valve
and lever the tyre out of the rim in this area (c). Hold the tyre lever tight in its
position. Slip the second tyre lever between rim and tyre at a distance of about
ten centimetres on the other side of the valve and lever the next portion of the
bead over the edge of the rim.
After levering a part of the tyre bead over the edge of the rim you should
normally be able to slip off the whole tyre on one side by moving the tyre lever
around the whole circumference. Now you can remove the inner tube. Make
sure the valve does not get caught in the rim, as this can damage the inner tube.
If necessary, you can remove the whole tyre by pulling the other tyre bead off
the rim. Repair the puncture according to the instructions of the repair kit manu-
facturer or replace the inner tube by a new one.
When you have removed the tyre, you should also check the rim tape (d). It
should lie squarely in the rim trough, covering all spoke nipples, and should nei-
ther be damaged nor brittle.
DANGER!
G
If the fabric of the tyre is destroyed by the perforating object, replace the
tyre to be on the safe side.
NOTE!
I
If you get a puncture en route, inflate the inner tube and bring it close to
your ear. In most cases you can hear the air coming out. At home you can
help yourself with a bucket of water where you can locate the hole by the bub-
bles. When you have found the hole, look for the corresponding place on the
tyre and check it, as well. Often, you will find a foreign body sticking in the tyre,
which ought to be removed. Otherwise another puncture can occur.
Tyre mounting
When mounting a tyre make sure no foreign matter, such as dirt or sand, gets
inside the tyre and you do not damage the inner tube in the process.
Slip one bead of the tyre onto the rim. Using your thumbs, press one bead over
the edge of the rim and then around the entire circumference (b). This should
normally be possible without using tools.
Stick the valve of the inner tube through the hole in the rim (e). Inflate the inner
tube slightly so that it becomes round and push it into the tyre all the way round
(f). Make sure not to leave any folds in the inner tube.
To finish mounting the tyre, start at the opposite side of the valve. Using your
thumbs, press as much of the second bead of the tyre over the edge of the rim
as you can.
Make sure the inner tube does not get pinched and squashed between the tyre
and the rim. You can prevent this by pushing the inner tube into the hollow of
the tyre with a finger as you work along.
Work the tyre into the rim by approaching the valve symmetrically from both
sides. Towards the end, you will have to pull the tyre vigorously downwards to
make the already mounted portion of the tyre slip towards the deepest part of
the rim well. This will ease the job noticeably on the last centimetres.
Before fitting the tyre completely on the rim check again whether the inner tube
lies properly inside the tyre and press the last stretch of tyre over the edge of
the rim using the balls of your thumbs (b).
If this does not work, you will have to use the tyre levers (c). Make sure the bent
ends point towards the inner tube and the inner tube does not get damaged.
Push the valve a little into the tyre so that the inner tube does not get caught
between the rim and the tyre beads. Check whether the valve stands upright. If
not, dismount one bead again and reposition the inner tube.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scott MTB E-bike 2018 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scott MTB E-bike 2018 in the language / languages: English as an attachment in your email.

The manual is 1.29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scott MTB E-bike 2018

Scott MTB E-bike 2018 User Manual - German - 89 pages

Scott MTB E-bike 2018 User Manual - French - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info